extrusion characteristics 中文意思是什麼
extrusion characteristics
解釋
壓出特性- extrusion : n. 1. 擠壓，擠壓成形；擠出。2. 逐出。3. 【地質學；地理學】（熔巖的）噴出；突出，伸出。
- characteristics : 產品性能描述
-
The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation
高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。 -
The development history of preparation technology of reactive extrusion dynamic vulcanization for thermoplastic dynamic vulcanizates was introduced, and reactive extrusion dynamic vulcanization technology, including its characteristics, preparation technology conditions, vulcanization rate and vulcanization process, was systematically discussed
摘要介紹了制備熱塑性動態硫化膠的反應擠出動態硫化技術的發展歷史，系統論述了該技術的特點、工藝條件、硫化速率及硫化過程。 -
On the basis that characteristics of every forming methods have been summarized and concluded, according to the moving relationship between working parts of die and block, it is proposed the successive partial plastic forming methods for groove have been divided to two kinds of basic deformation styles, rolling and splitting extrusion
在總結歸納各種方法變形特徵的基礎上，根據模具工作部分與坯料之間的運動關系，提出槽的連續局部塑性成形可劃分為滾軋與劈擠兩種基本變形方式。 -
This machine is willing to have a high production ability, the gum anticipates temperature low, the electric power consumes little, quality good, the petrochemistry even etc. characteristics, so used for the gum tube, inner tire broadly, tape inner pad layer, seal completely, electric wire, electric cable, protect the ware extrusion of a set of etc. rubber to prepare to take shape
用途介紹:本機具有生產能力高，膠料溫度低，電能消耗少，混合質量好，塑化均勻等特點，因此廣泛地用於膠管，內胎，膠帶內襯層，密封條，電線，電纜，護套等橡膠製品擠出預成形。 -
The characteristics of the reactive extrusion synthesis technique of poly ( lactic acid ) ( pla ) and the devolatilization technique for pla are introduced, and the key point and influence factor of the devolatilization in during the synthesis by reactive extrusion are analyzed
摘要主要介紹了反應擠出合成聚乳酸的技術特點和脫揮技術應用；分析了反應擠出合成過程中脫揮處理的關鍵點和影響因素。 -
The characteristics of al alloy plastic deformation have been analyzed with discussion about shaping technology of forging, extrusion etc. and introduction to use of al alloy in automotive industry
摘要分析了鋁合金塑性變形特點，討論了鋁合金的鍛造、擠壓等變形工藝，同時介紹了鋁合金在汽車工業中的應用情況。 -
Based on the physiological characteristics and the nutritional requirements of marine fish, the feeds are formulated with high quality feedstuffs and additives and processed by advanced extrusion processing technology
根據飼養動物的生理學特點及生長的需要，採用優質原料，經過科學配方用先進膨化擠壓工藝加工而成。
分享友人