extrusion die 中文意思是什麼

extrusion die 解釋
擠出模
  • extrusion : n. 1. 擠壓，擠壓成形；擠出。2. 逐出。3. 【地質學；地理學】（熔巖的）噴出；突出，伸出。
  • die : vi （died; dying）1 死。2 滅亡，消滅；熄滅；枯死，凋落。3 漠然不受影響，感覺不到 （to） 。4 泄氣...
  1. Cermet hot extrusion die blank

    金屬陶瓷熱擠壓模坯
  2. The inside fashion of the sway oil pump stator is complex, its wall thickness is pockety and the metal flow law is difficult to master. at the present time, the investigation of warm extrusion forming technique for the nonuniform wall thickness forging has few to been done. the forming technique and die configuration which use for production have not achieve optimization

    由於轉向油泵定子的內部形狀復雜，零件壁厚分佈不均，金屬流動規律難于掌握，目前人們對這種非均勻壁厚鍛件的溫擠壓成形工藝研究幾乎沒有，其成形工藝及生產用模具結構並未達到最優化。
  3. According to the above theories, with using the software - deform - 3d, we have made the numerical analog simulation and analyse the warm extrusion forming technique process for sway oil pump stator, optimized the forming : technique and the die parameter for the pockety wall thickness forging this paper concretely analysis and research metal flow ' s characterize in different forming processes

    本課題根據上述理論，利用有限元數值模擬模擬軟體deform - 3d ，對轉向油泵定子溫擠成形工藝過程進行模擬模擬分析，優化了油泵定子的成形工藝及模具參數。
  4. Hot extrusion technology and die design of oxygen spray nozzle

    氧氣噴頭的熱擠壓工藝及模具設計
  5. In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production

    論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。
  6. Abstract : to decrease bending and twist deformation of non - sym metry extruded sections, a new conception of local extrusion ratio and die band ratio has been set up, and also the formulas for the place of die hole on the ba sis of simulating test

    文摘:為減小非對稱型材擠壓的彎扭畸變，在試驗研究的基礎上，建立了局部擠壓比、擠壓帶系數的概念，擠壓筒中心與擠壓模孔型中心相對位置的計算式。
  7. Cold punching extrusion die of silicon steel of cold punching extrusion die and study on eompound infiltration strengthening

    硅鋼片冷沖凹模的選材與復合強化處理研究
  8. In order to improve the quality of the extrusion mold and reduce the cycle time, a lot of research about cad / cae / cam of system the extrusion die have been done

    為了保證鋁型材擠壓模具的質量，延長模具壽命，人們已經在鋁型材擠壓模具cad cae cam技術方面進行了長期和不懈的努力。
  9. Design of cold extrusion die of piston pin

    活塞銷冷擠壓模具設計
  10. The applications of steel - hard alloy in hot extrusion die

    鋼結硬質合金在熱擠壓模具上的應用
  11. Numerical simulation of three dimensiona isothermal power - law polymer melt flow within an extrusion die with the quot; l quot; shaped cross section

    型異型材擠出口模內聚合物熔體三維等溫冪律流動的數值模擬
  12. Numerical simulation and analysis of polymer melt filling flow driven by a periodically oscillating entrance pressure through the extrusion die with an irregular cross - section

    振動場作用下聚合物熔體在異型材擠出口模內的充填流動分析
  13. Experienced with mechanical drawing and extrusion die design

    具備機械制圖和擠出模具設計經驗。
  14. Our company is mainly manufacture extrusion die, blowing die head, air bubble die, stretch film die, foam die, coating die, screen changer, have complete equipment, strong technical force, enjoying high trust and support of our customers

    我廠是專業生產擠出平模、吹塑模具、氣墊模具、流延模具、發泡模具、塗覆模具、換網的廠家，設備齊全，技術力量雄厚，贏得國內外客戶的依賴和支持。
  15. Working portion of cold extrusion die

    冷擠壓模具工作部分
  16. Forming process for the flexible aluminum pipe and design of cold extrusion die

    鋁質軟管冷擠壓成形工藝及模具
  17. The full three dimensional isothermal viscoelastic numerical simulation on the extrusion die swell of polymer profile

    聚合物異型材擠出脹大全三維等溫黏彈性的數值模擬
  18. Study on the stress distribution of cold extrusion die under inner pressure

    冷擠壓模受內壓作用應力分佈規律的研究
  19. Development of hot extrusion die for zf16 - 252 contact pedestal used in high voltage switch

    高壓開關觸頭座熱擠壓模設計
  20. Application of bp artificial neural network and genetic algorithm to the parameters optimization of profile extrusion die

    人工神經網路與遺傳演算法在型材擠壓模具參數優化中的應用
分享友人
分享到 Line

分享到臉書