extrusion rate 中文意思是什麼
extrusion rate
解釋
壓出速度-
08. 01 flow rate of thermoplastics by extrusion plastometer, test method for
擠壓式塑性計測試熱塑性塑料流速的方法 -
The intercalating rate of modifier was 27. 3wt %. fourier - trandformed infrared spectroscopy ( ft - ir ) also shows that modifier has been between layers. a series of polyamide / montmorillonite nanocomposites were prepared by melting extrusion method in two - screwed extruder at first
首次對三元尼龍和蒙脫土復合進行了研究， tem結果表明：粘土片層雜亂無章地分散在基體中，平均厚度10nm ，形成剝離型納米復合材料。 -
The development history of preparation technology of reactive extrusion dynamic vulcanization for thermoplastic dynamic vulcanizates was introduced, and reactive extrusion dynamic vulcanization technology, including its characteristics, preparation technology conditions, vulcanization rate and vulcanization process, was systematically discussed
摘要介紹了制備熱塑性動態硫化膠的反應擠出動態硫化技術的發展歷史，系統論述了該技術的特點、工藝條件、硫化速率及硫化過程。 -
The operating rate of extrusion machine in china is only 35 % or so, which falls long distance behind of the developed countries " level, and is less 30 % than the world average operating rate. over the 90 % of china ' s aluminum section for building belong to the low level product, the rate of high additional value product is low, and is lack of the famous brand
而中國擠壓機的開工率僅為35 %左右，遠遠落後于發達國家水平，比世界平均利用率低30個百分點。我國建築鋁型材90 %以上在國際市場上屬低檔產品，高附加值產品比重低，缺乏著名品牌。缺乏國際競爭力。 -
In the presence of hx, oocyte maturation to mil and the extrusion of polar body were highly synchronized, the oocytes matured to mil stage were activated in higher rates than oocytes matured without hx, and those oocytes matured exposed to hx for all the 24h showed a high rate ( 55 % ) of spontaneous activation
Hx存在情況下成熟到m期的卵母細胞排出第一極體時同步化程度高，其孤雌活化能力高於正常成熟卵母細胞， hx作用24h組出現自發激活現象（自發活化比率55 ） 。 -
Through orthogonal experiment design, the preparation technology of reactive extrusion dynamic vulcanization for low hardness epdm / pp blend thermoplastic dynamic vulcanizates was studied, and the effects on micromorphology of extruded vulcanizates of such main technological factors as barrel temperature, feed screw driven voltage and host machine screw rotation rate were discussed
摘要通過正交試驗設計，研究了低硬度epdm / pp共混型熱塑性動態硫化膠的反應擠出動態硫化制備工藝，初步探討了機筒溫度、喂料螺桿驅動電壓及主機螺桿轉速等主要工藝因素對擠出物微觀相態結構的影響。 -
Based on the data of vertical and horizontal displacements from a certain construction site in cixi city of zhejiang province, the validity of controlling earth - extrusion effects in saturated soft clay ground caused by statically piling was quantitatively analyzed and compared with different technical measures, including reduction of piling rate and installation of stress - relax holes
摘要根據在浙江省慈溪市某靜壓法沈樁施工現場所監測的地基土位移數據，定量分析比較了控制施工進度、設置應力釋放和排水深孔等工程技術措施對減輕飽和軟粘土地基沈樁擠土效應的有效性，並初步提出了現場地基土位移及其變化速率的監控標準。 -
Standard test method for extrusion rate of elastomeric sealants
彈性密封件擠壓比的標準試驗方法 -
Standard test method for extrusion rate and application life of elastomeric sealants
彈性密封料的擠壓率和使用壽命的標準試驗方法 -
In the making process we use hot - forging warm - forging cold extrusion forming and magnetic annealing processes to completely solve the problem of complex form hign precision dimensions difficult manufacturing lower power and so on. what s more, part surface is very smooth with no trimmed margin, continuous flowing metal fiber, high strength, lower noise. forged claw poles obviously increase generator s power and life, and also improve finished product rate of roughness
在製造過程中採用了熱鍛溫鍛冷擠壓成型及磁性退火等先進生產工藝徹底解決了精鍛「爪極」形狀復雜尺寸精度高製造難度大功率低等問題，且產品表面光潔無飛邊金屬流動纖維連續毛坯強度大噪音低，明顯提高了發電機的功率和壽命，並且提高了毛坯成品率。
分享友人