failure by shear 中文意思是什麼
failure by shear
解釋
剪切破壞-
Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。 -
Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield
摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果，指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段；討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響；提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議；最終給出了異型節點抗剪承載力的計算公式。 -
Abstract : based on the data obtained from field observations and deformation monitoring, this paper deals with the deformation and failure of a double - decked slope composed of soft rock strata in its lower part and hard - brittle rock strata in its upper part. it is demonstrated that the deformation of this kind of slopes is always initiated by the non - homogeneous rheological compression of the lower soft rock strata, leading to the tension fracture and toppling of the upper hard rock strata, and at last the sliding of the whole deformed body will be caused by the shear failure along the stress - concentration zone in the lower soft rock mass under the actions of the gravitational loading and infiltration water
文摘:以現場考察和變形監測資料為依據，探討一個下部有軟弱基座，上部為硬脆性坡體的「二元結構」邊坡的變形破壞問題，揭示這類邊坡的變形總是以下部軟弱巖體的不均勻壓縮流變為先導，進而引起上部硬脆性坡體的拉裂與傾倒，最終通過滲入水的作用，使下部承載狀況已進一步惡化了的軟弱巖體，沿剪應力集中帶發生剪切破壞而導致整個變形坡體的下滑。 -
In this paper, the researching and developing situating at home and abroad on aseismic properties of the masonry structures are reviewed. aiming to the defects of the calculated formulas of the aseismatic shear strength of brick walls in the code for seismic design of building ( gb50011 - 2001 ) and the code for design of masonry structures ( gb50003 - 2001 ), through test on brick wall models between the single wall and the wall with flanges, restoring force characteristics, the behavior at failure of the brick masonry wall and the effect of longitudinal wall under cyclic horizontal loading were analyzed the aseismic capacity has increased by 31 % for wall with flanges, the rigidity and deformation of the wall has gone up greatly too. the conclusion that the effect of longitudinal wall should be comprised in the aseismatic formulas was proposed
本文回顧了國內外關于砌體結構抗震性能的研究與發展現狀，針對建築抗震設計規范（ gb50011 - 2001 ）和砌體結構設計規范（ gb50003 - 2001 ）中墻體抗震驗算公式中的不足之處，通過單片墻和帶翼緣墻在垂直荷載和水平反復荷載作用下的對比試驗，研究了帶翼緣墻在水平反復荷載作用下的恢復力特性曲線、磚墻破壞特徵以及縱墻的影響等，翼緣墻的存在，主墻抗剪能力可以提高31 ，剛度及變形能力也均有較大提高的結論，墻體驗算公式中應當考慮縱橫墻共同作用的影響。 -
The reason for the failure of loosely residual soil slopes triggered by rainfall is that the contractive failure caused by the penetration of rainfall, giving rise to a high excess pore pressure which reduces shear strength of the soil. the soil is prone to flow slide after failure under the action of gravity due to its high moistu re content
蔣家溝地區坡殘積土斜坡在暴雨條件下的破壞是由於降雨入滲導致土體發生剪縮破壞，破壞後土體的孔隙水壓力升高形成超孔隙水壓力、土體強度降低、破壞迅速擴展所致，因而大多數斜坡呈流滑型破壞並具有突然性破壞特點。 -
Make using of the critical point of the arch failure transiting to the tooth failure ( which is also the point when the non - stirrup beam ' s shear bearing capacity arrives to its minimum ) which is advanced in the arch - tooth theory of beams without shear reinforcement by g. kani and the critical point of the diagonal - tension failure transiting to the shear - compression failure which is advanced in the anti - theory, the minimum shear resistance of general bea ms which is destroyed in the range of shear - compression failure is advanced
利用g . kani提出的拱?齒理論中的無腹筋梁的拱齒破壞的分界點（也就是無腹筋粱的最小抗剪承載力點） ，再結合前述理論中所提出的梁剪壓破壞和斜拉破壞的分界點，提出了梁在延性的剪壓破壞范圍內的最小抗剪承載力，並與混凝土結構設計規范gb50010 - 2002比較，結果吻合較好。 -
The minimum shear resistance of beams in the paper is close to the one in the code for design of concrete structures " gb50010 - 2002 '. according to the actual project, the destroy of 448 kinds of beams are analyzed by computer by taking account of the effective coefficient " " of the strength of concrete confined by hoops, the relationship with the section property of beams, the critical point of the arch - rib failure transiting to the shear - compression failure which is advanced in the anti - theory, and the contribution to the beam ' s shear resistance of the concrete in the shear - compression zone
引用箍筋約束混凝土的有效系數，利用其與梁截面特性的關系並結合理論分析中提出的梁剪壓破壞與斜壓破壞的分界點，同時考慮了剪壓區混凝土的抗剪貢獻，從工程實際出發，編程擬算了448種梁構件的破壞情況，計算結果表明，梁發生在剪壓破壞范圍內的最大抗剪承載力值比混凝土結構設計規范gb50010 - 2002值略高。 -
According to the demand of 《 code for seismic design of building 》 ( gb50011 - 2001 ), furthermore, based on the experimental study of two 1 / 15 reduced - scale shear wall models under low frequency cyclic and reversed lateral loads, the interacting behavior of the r. c frame column and the shear wall is studied, the failure mechanism and energy dissipation mechanism of moderate and tall shear wall with r. c frame column are compared, the seismic behavior is evaluated by the comparison of strength, stiffness, ductility, restoring force characteristics as well as energy consumption ability. it was showed by the experimental results that the earthquake resistant energy dissipation ability of the shear wall with frame column is satisfactory
因此，為了探討這類剪力墻結構的抗震性能，本文以我國現行《建築抗震設計規范》 （ gb50011 - 2001 ）的要求為基礎，通過1 15的縮尺比，將一縱向框架一剪力墻原型結構中的剪力墻結構模擬為一個試驗模型並對其進行了偽靜力加載試驗，研究了墻板與邊框柱的共同工作性能，分析了帶邊框柱中高剪力墻的受力特點、破壞及耗能機理，並從承載力、剛度、變形、延性及恢復力特性等方面綜合評價了其抗震性能，得出了一些有益的設計理念和方法。 -
The major contents are as following : through a test of 1 / 15 - scaled model, the shear wall of a longitudinal frame - shear wall structure main factory building of the large power plant is modeled as testing model structure, and is tested by pseudo static test. this paper mainly investigates the loading behavior, failure proceeding, strength, rigidity, deformation, ductility and energy dissipation capacity of the model structure
主要內容如下：採用1 15縮尺比，把某大型火電廠主廠房縱向框架?剪力墻原型結構中的剪力墻模擬為試驗模型結構，並對其進行偽靜力加載試驗，研究了此類結構的受力特點、開裂與破壞過程、承載力、剛度、變形、延性及耗能性能等問題。 -
Standard test method for creep and time to failure of adhesives in static shear by compression loading wood - to - wood
用壓縮負荷靜剪切法法測定膠粘劑蠕變和老化時間的標準試驗方法 -
Coupling beams " failure mode, shear distortion, ductility and energy dissipation were impacted by different shear - compression ratio from 0. 15 to 0. 20
是一種值得推薦的抗震聯肢墻小跨高比洞口連梁的配筋形式。 -
Results show that clamping angle dominated displacement of anchorage and failure mechanism : surrounding rock and soil compaction is induced by small clamping angle, instead, shear failure occurs in neighborhood soil of leading end of anchorage while clamping angle is big ; anchorage length influenced surrounding rock stress as nonlinear self - organization critical characteristic on interface ; anchorage size contribution to systemic primary monitor parameter is relatively uniform
研究發現：夾持角控制著錨碇變位和破壞機理，夾持角過小時錨碇壓密圍巖土體，較大時錨碇前端附近土體則產生剪切破壞；錨碇長度影響接觸面圍巖應力量值，表現為非線性的自組織臨界特徵；錨碇體粗細對系統主要監控參數的貢獻相對均勻。 -
Research has been done on the calculating methods of lateral stiffness and bearing capacity of the frame. according to experimental studies, finite element analysis and theoretical analysis, it develops to calculate lateral stiffness of frame with special - shaped columns of greater height - width ratio by using frame with rigid zones, and considering shear deformation of beam and columns. without considering the torsion of the whole structure, assuming the special - shaped column in the rc frame is flexural failure under uniaxial eccentricity force, putting forward the calculation method of flexural strength of special - shaped columns and the shear strength in a story for r. c
對異形柱框架分別按普通框架和壁式框架進行分析，並與空間有限元分析結果和試驗結果進行比較，提出了異形柱框架結構側向剛度的計算方法；在整體結構不產生扭轉且異形柱為彎曲破壞的假定下，提出了異形柱的受彎承載力及受剪承載力計算公式；提出了根據異形柱框架結構的破壞機構確定其樓層受剪承載力的方法。 -
To guarantee the stability of the frame in strong earthquake motion, and on the basis of analysis on the concept of “ capacity design ” in the above three countries seismic design provisions, it is advised that the moment amplification coefficients at the bottom sections of columns for the frame structures in some seismic intensity be increased to reduce the possibility of the frame column yielding. taking the above three countries seismic codes as reference, it is recommended that it be added details of seismic design by using diagonal shear reinforcement to safeguard beams against sliding shear failure, when the positive - negative shear forces are reverse and the ratio is high
為了保證在大震作用下框架結構的穩定性，借鑒國外規范「柱-梁承載力級差系數」的思想，本文提出了對部分抗震等級的框架結構的柱端抗彎能力增強系數應予以提高，以降低框架柱屈服的可能性;參照國外有關規范的發展，本文建議對于正、負剪力反向且比值較大的框架梁宜增加交叉斜筋，以防止沿垂直裂縫發生嚴重的剪切錯動。 -
Based on the result of failure by shear of recycled concrete beams and using the ultimate equilibrium theory, a formula for the shear strength of recycled concrete beams is recommended
根據13根再生混凝土梁的剪切破壞結果，依據極限平衡理論，提出再生混凝土梁受剪承載力的計算公式。 -
Based on the direct shear test of double - asperity joints include two tooth - shaped asperities, the shear properties of double - asperity joints are analyzed according to the difference of two asperities ' angles, and the failure mechanism of double - asperity joints and the effects to joints ' failure mode and shear strength produced by the order of two asperities are discussed
摘要通過對由兩個齒形凸體組合構成的雙齒節理進行直剪試驗，分析了兩個齒形凸體的起伏角相等時和不等時雙齒節理的剪切特性；觀察和分析含兩種不同起伏角凸起體的雙齒節理的漸進破壞過程與機理，以及兩個齒形凸起體的排列順序對此類雙齒節理的剪切強度和變形特性的影響。 -
By means of a mass of shear strength test of rough cement face of concrete - bedrock, influences of cement face roughness of two mediums on shear strength parameter, shear deformation characteristics, shear failure mechanics are systemically studied. empirical relationship between fractal dimension of cement face roughness and shear strength parameters is established
通過大量的混凝土?基巖粗糙膠結面抗剪強度試驗，系統研究了兩相介質膠結面粗糙度對其抗剪強度參數值大小、剪切變形特徵、以及剪切破壞機理的影響，建立了膠結面粗糙度分維數與抗剪強度參數之間的經驗關系式。 -
Real - time ct scanning observations reflecting the expansiveness and strength variation are carried on. the structural changes during the course of consolidation, shear failure, swelling and water saturated shear failure are analysed by means of ct images
根據ct圖像的變化，分析膨脹土固結前後、剪切破壞、加水膨脹變形、飽和后剪切破壞過程中膨脹土的結構變化。 -
If the gap between two branch members is great, the joint is treated as t - or y - joint. or else, the minimum of the results obtained by the formula based upon steel tube flange shear failure mode and effective width failure mode is adapted for the tension branch joints
給出了矩形鋼管混凝土k型節點的間隙判斷公式，間隙較大時按t 、 y型節點計算；間隙較小時受拉支管節點承載力按沖剪破壞和有效寬度破壞模式計算，取較小值。 -
This paper mainly introduces technologies of bending carbon fiber reinforced plastic ( cfrp ) plates or fabrics to the web of reinforced concrete members, and also this paper discusses the design principles of carbon fiber reinforced plastic ( cfrp ) used in the reinforced concrete members, as well as considering the preload effect to the bending capacity of the reinforced concrete members. finally, a kind of new practical method is put forward, and may be a reference for practical engineering designer. in the meantime, this paper analyzes the " local failure " caused by shear and normal stress concentrations at the plate ends that can easily incorporated into design equations. furthermore, the bonding and anchoring conformation of concrete members strengthened by carbon fiber reinforced plastics also be set forth
本文重點研究碳纖維製成織物片材粘貼到混凝土表面用於結構的補強與加固的技術特點，從理論上探討cfrp加固混凝土結構的設計原理，分析二次受力對加固結構的彎矩承載力的影響；同時對外貼碳纖維加固混凝土的抗彎和抗剪提供一種簡單、實用的設計方法，供工程設計人員參考，對碳纖維布加固混凝土梁中出現剝離破壞也進行了分析，提供了最大剝離正應力的計算公式，以及對外貼cfrp加固結構構件的粘貼構造與錨固進行了闡述。
分享友人