filling fiber 中文意思是什麼
filling fiber
解釋
纖維填料-
With the filling of diabase, the mechanical properties of the composite increased first and then decreased with a top tensile strength of 56. 5mpa and a top impact strength of 70. 1mpa. these illuminated that the diabase fiber reinforced pvc composites could be used as structure materials
復合材料的力學性能隨著輝綠巖的增加先升后降，復合材料拉伸強度最高可達56 . 5mpa ，復合材料沖擊強度最高可達70 . 1mpa ，說明輝綠巖纖維增強pvc復合材料作結構材料使用。 -
The filling gels for fiber loose - tube are generally divided into two categories according to the thixotropic gels of which they are composed
摘要光纖松套管填充油膏以其所含膠凝劑的不同分為兩大類。 -
The methods of compounding then with fiber or textiles, such as composite spinning, hollow fiber filling, textile coating and micro - encapsulation, are exemplified and compared
例舉復合紡絲法、中空纖維填充法、織物塗層后整理法、微膠囊法等相變材料與纖維或紡織品的復合方法，比較各種復合方法的特點與優劣。 -
Sealing, filling and coating film metals, carbon fiber, woods, plastics and batteries etc. tools or vessels
金屬、碳纖、木材、塑膠、蓄電池等工具或容器之灌注及塗覆。 -
According to the experiment of influences of fiber structures and the width of edge channel on flow filling, it was found that even a small gap ( l or 2mm ) between the preform and the mold edge could also disrupt the flow pattern, which evidently changed the local permeability of preform. the filling process was simulated using the permeability for different edge width predicted by a. hammami or poiseuille model, which shown good agreement with the experiment results
實驗研究了纖維鋪層結構及流道縫隙的寬度對充模流動的影響，發現在纖維預成型體和模具壁間存在的較小的縫隙也會對邊緣的流動產生干擾，進而影響增強材料主體的滲透；對于不同的縫隙寬度，分別根據a . hammami模型和poiseuille模型預測邊緣等效滲透率，並進行充模過程數值模擬，與實驗結果吻合較好。 -
Made of high - speed mixing polytetrafluoethylene resin and a certain volume of filling agent ( such as carbon fiber, graphite, molybdenum disulfide, glass fiber and bronze powder etc. ) shaped by moulding then through high heat sintering
用聚四氟乙烯樹酯與一定量的填充劑（如：碳纖維、石墨、二硫化組、玻璃纖維、青銅粉等）經高速混合均勻後用模塑成型經高溫燒結製成。 -
Based on the requirement and target of the projects, firstly, pcf bragg grating are investigated theoretically and experimentally. moreover, the effects of filling high refractive index material ( nematic liquid crystal, nlc ) in pcfs on the transmission mechanism and propagation properties are studied by using plane - wave method and finite - element method ( fem ), farther, several novel pcfs are proposed and designed. lastly, we propose and demonstrate a clad - pumped er3 + / yb3 + - codoped fiber laser, which integrate all performances of broad - band tunable wavelength, uniform output power spectrum, high repeat frequency and high average power to together
本論文選題于國家973 、 863以及國家自然科學基金等項目，結合課題的要求和主要目標，在對光子晶體光纖（ pcfs ）傳輸特性研究的基礎上，首先對光子晶體光纖光柵進行了理論和實驗研究;然後，採用平面波展開法和有限單元法分析了在光纖的空氣孔中填充高折射率液晶對光纖傳導機制和傳輸特性的影響，提出並設計了幾種新型光子晶體光纖;最後，提出並研製成功連續可調諧、輸出功率譜均衡的全光纖化、高功率包層泵浦鉺鐿共摻光纖激光器實驗樣機。 -
Based on the essential elucidation on their respective thixotropic mechanisms, with the help of the rheogeniometer, the tests of the two representative fiber filling gels ' rheological properties including thixotropy and yield stress were carried out
文章在闡明它們各自增稠觸變性機理的基礎上，採用流變儀檢測了兩種有代表性的光纖油膏的流變學性能，其中包括觸變性和屈服應力。 -
It is proved that polypropylene fiber concrete performs well in resisting impact, abrasion and crack, and thus well applicable in sandy flow region characterized in high speed and turbulence, such as the filling & emptying culvert of shiplock, etc
表明聚丙烯纖維混凝土具有良好的抗沖耐磨性能和抗裂性能，可較好地應用於船閘輸水廊道等處于高速、紊亂、含沙水流區。 -
Regarding the lcm filling process as the newton fluid through fibrous reinforcements, the permeability of preform determines the saturating of resin in fiber, and has effects on the curing process and the quality of products. based on the darcy ' s law, the theoretical model of permeability measurement was established. and the influence of different testing methods and major process parameters such as fabric structure, fiber volume fraction, injection pressure, flow rate and resin viscosity on preform permeability were investigated in details
文中首先根據達西定律建立了滲透率測量的理論模型，深入研究了不同的測試方法及主要工藝參數（纖維織物織構、纖維體積含量、充模壓力、流動速度、樹脂粘度）對滲透特性的影響規律，發現多孔介質增強材料的滲透率主要取決于纖維織物的結構形式，預成型體孔隙分佈及其體積分數、壓實性對滲透率有較大的影響，提高充模壓力和流動速度可以縮短充模時間，在一定程度上可以提高滲透率。 -
Results show that the properties of process droped along with the filling of the diabase fiber, but the balance torque was less than 50nm when the content of the diabase fiber was less than 30phr, the diabase fiber / pvc composite could be processed by traditional technics. ir showed the chemic reaction take place between the coupling agents and the fiber
研究結果表明：盡管輝綠巖纖維pvc復合體系的加工性能隨輝綠巖纖維含量的增加而下降，但當輝綠巖纖維含量小於30份時，輝綠巖纖維pvc體系的平衡轉矩小於50nm ，說明當輝綠巖纖維含量小於30份時能夠採用傳統加工方法進行加工。 -
Based on the basic principles of densified systems containing homogeneously arranged ultra - fine particles ( dsp ) and reactive powder concrete ( rpc ) adopted by foreign researchers specialized in building materials, silica rume, ultra - fine fly ash, quartz powder, 52. 5 - class portland cement and superplasticizer were selected and mixed, the theoretic of mixed steel fiber reinforced cement - based composite materials and of micro - aggregate filling voids were applied, the composition was adjusted, the mixture ratio of rpc was optimized, a suitable curing schedule was adopted, in the result, an ultra - high performance concrete designated rpc was successfully prepared by normal technology methods
本文基於超細粒聚密材料（ dsp ）和活性粉末混凝土（ rpc ）配製的基本原理，選用硅灰、粉煤灰、石英粉和硅酸鹽水泥，輔以高效減水劑，採用多重復合的技術路線，運用混雜鋼纖維增強理論和微集料填充密實原理，調整材料組成，優化混凝土配合比，結合適宜的養護制度，在現有技術條件下，成功制備出了rpc200材料。 -
The main applications of these fiber rods are light polymerization of dental cavities filling material and light illumination for dental turbine handpiece
光纖光導棒主要應用范圍是牙醫用補牙固化機以及磨牙手機的光線傳導。 -
( 4 ) compared with other fillers, the performances of wollastonite filling composite system are super to that of calcium carbonate and talcum filling systems, and are near to that of asbestos and glass fiber filling systems
（ 4 ）與其它pp填充礦物相比，硅灰石填充復合體系的綜合力學性能優于碳酸鈣和滑石的填充體系，並可與石棉、玻璃纖維的填充體系相媲美。 -
Fiber optic cable filling machine
光纜填充機
分享友人