filling-defect 中文意思是什麼
filling-defect
解釋
充盈缺損-
Intravenous urography, retrograde pyelography and computed tomography all showed a filling defect in the lower calx of left kidney
在文獻上使用過的名稱包括纖維瘤、纖維表皮細胞瘤、纖維息肉、纖維表皮性息肉及缺陷瘤性息肉等。 -
His shyness, which was so painful as a defect, filling him with a mild complacency now that it was regarded as an interesting study.
他的靦腆是一種使他痛心疾首的缺點，而現在被當成了一個有趣的，值得探討的問題，這使他的心裏充滿了淡淡的滿足感。 -
His shyness, which was so painful as a defect, filling him with a mild complacency now that it was regarded as an interesting study
他的靦腆是一種使人他痛心疾首的缺點，而現在被當成了一個有趣的，值得探討的問題，這使他的心裏充滿了淡淡的滿足感。 -
Attentions have to be paid to coating ingredient, smearing, sand filling and compaction for metal seeping defect prevention
闡明了為防止滲金屬缺陷，在塗料配製、塗掛、加砂緊實中應注意的問題和具體工藝。 -
In this paper are analyzed the causes of light filling bar in weaving fine viscose / flax fabric caused by machine and operation with the technical measures to minimize this defect and the achieved result detailed
摘要分析了織造過程中機械故障和操作過程中造成粘麻細布稀密路疵的原因，具體介紹了降低稀密路疵點的技術措施和所取得的效果。 -
The results showed the optimum condition and technology were that mma : ea : maa = 45 : 40 : 15, the content of total initiator was 0. 8 %, and the content of seed initiator was 0. 3 %, emulsion : talcum powder : water = 200 : 80 : 60, and the defect of too sticky of working liquid could be overcame by using talcum powder as filling agent
結果表明：單體組成比為mma ： ea ： maa 45 ： 40 ： 15時，所得乳液聚合物能滿足使用性能要求；種子引發劑加入量控制在單體量0 . 3 % ，而總的引發劑用量在0 . 8 %較適宜；以滑石粉作填料，可克服工作液增稠嚴重的缺陷，工作液的配比按膠乳：滑石粉：水質量比200 ： 80 ： 60能得到理想港寶膠片。 -
Reference to the designation of die casting mould, we put forward some kinds of projects respect to the design and manufacture of dies of the special purpose machine. and we simulate die casting filling process 、 surface defect distribution and temperature field etc. of az91d magnesium alloy shell part with flow3d software
設計時將參照壓鑄模的設計方法，提出多種方案，並使用flow3d模擬設計軟體來模擬金屬液的填充過程，預測可能產生缺陷的位置，從而決定澆注系統的形狀和分佈，冷卻水道的流向和位置，分流錐的大小和位置。 -
Abstract : a new algorithm of area filling of geometry graph has been proposed. in this algonthm based on the area calculating theory of closed graph with curvilinear integral. the redundant judgement of inner pixels in the area has been eliminated and the defect of polygon area filling algorithm, which has some limitations to the graph shape, has also been overcome
文摘:基於曲線積分求封閉圖形區域面積的基本原理，提出了一種新的幾何圖形區域填充演算法.該演算法不需要對區域內點進行重復判斷，也克服了多邊形填充演算法對區域形狀有一定要求的缺點 -
This research is dedicated to investigate the relationship between the permeability and technical parameters and solve the defect of low producing efficiency due to inadequate impregnating and filling in lcm, which provide theoretical support and practical guidance for procedure design and manufacture to enhance the controllable capability. it also has significant influence on the development of composites manufacturing techniques with high quality and low cost
本論文的研究工作致力於建立滲透率與工藝參數的相互關聯，解決lcm技術因滲透不良、充模不滿，廢品率高的缺點，為lcm技術的流程設計和工藝生產提供理論依據和實踐指導，進一步提高工藝的可控制性，同時對促進高性能低成本先進復合材料制備技術的發展也具有重要的意義。
分享友人