flow-nozzle 中文意思是什麼

flow-nozzle 解釋
測流量的噴嘴
  • flow : vi 1 流，流動。2 （血液等）流通，循環。3 流過；川流不息；（時間）飛逝；（言語等）流暢。4 （衣服、...
  • nozzle : n. 管嘴；噴嘴；〈俚語〉鼻子。 a jet [propelling] nozzle 【火箭】尾噴管。
  1. The nozzle flow is composed of the main gas stream and the secondary air stream in order to simulate the nozzle of turbofan engine

    噴管中的氣流由主流燃氣和次流空氣組成，用以模擬渦扇發動機的噴管。
  2. In final section of this paper, the flow field of two types of supersonic nozzle for scramjet is simulated and analyzed

    最後，本文針對兩種構型的超音速尾噴管，對其流場進行了計算和分析。
  3. Research on the flow characteristic of spray nozzle and design

    噴嘴水力性能分析及設計
  4. Experimental research on the flow characteristics of an air atomizing spray nozzle

    氣動旋流霧化噴嘴流動特性
  5. According to rigorous procedures, an experimental study was carried out to investigate the effects of jet exit velocity, flow direction, fluid subcooling and nozzle diameter on hysteresis of boiling heat transfer with impinging circular submerged jets of highly - wetting liquids

    摘要系統地研究了液體在圓形斷面噴嘴浸沒射流作用下沸騰熱滯后與射流沖擊速度大小、液體流動方向、液體過冷度和噴嘴直徑等因素的影響。
  6. This paper described a cold gas simulation of solid rocket motor with submerged nozzle. a two - dimension model with rectangular channel was designed, which can simulate different flow conditions at three periods after ignition

    本文從冷流模擬的角度出發，設計了通道為矩形的含潛入噴管發動機冷流模型，可以模擬發動機工作過程中三個不同時刻的流動狀態。
  7. The effects of reynolds number, back surface of nozzle, aft - dome configuration and degree of submergence on aft - end internal flow were studied by both cold gas simulation and numerical simulation. it is showed that the separated flow is sensitive to the change of reynolds number and aft - end cavity configuration

    最後，利用冷流模擬與數值模擬相結合的方法，研究了雷諾數、噴管背壁形狀、后封頭形狀和潛入深度對燃燒室尾部流場的影響，結果表明流動的分離對雷諾數和背壁區幾何邊界的變化很敏感。
  8. 2. using cfd software - fluent, many flow states were been simulated. these states are the influence of nozzle structure with the flow, the distributing characteristic of inside flow, the influence of cold gas flow and outside flow with the work of the nozzle, the change of inside pressure load when the nozzle regulates

    2 、藉助cfd軟體fluent ，計算出可調噴管本身結構對流動的影響、可調噴管流場的參數分佈、冷卻氣流對噴管流動的影響、外流對可調噴管內流的影響、噴管的冷流流場和噴管調節過程中內壁面的壓強載荷變化。
  9. A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle

    試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。
  10. The nozzle diameter and the ejection pressure have a great effect on the flow rate 、 droplet cone shape 、 droplet size and cover area of fluid pesticide

    噴嘴孔徑和噴出壓力在很大程度上影響著藥液的流量特性、霧錐形狀、霧滴大小和覆蓋面積。
  11. According to the experimental data of droplet size 、 particle spectrum range 、 droplet cone shape 、 flow rate 、 cover area and cover area rate which obtained through changing the pressure of power sprayer and the nozzle diameter in greenhouse ， this paper made comparative analysis on atomizing performance in same pressure and different nozzle type between same nozzle type and different pressure. the conclusion is that : the ejection rate and the droplet cone shape change with the variation of pressure and nozzle diameter ， average particle diameter decreases obviously and particle quantity increases obviously with the increase of pressure and decrease of nozzle diameter. these results will lay experimental foundation for precise spraying 、 low pollution and highly effective operation

    本文根據溫室內動力噴霧機壓力與噴嘴孔徑的變化影響霧滴大小、粒譜范圍、霧錐形狀、流量、覆蓋面積及覆蓋面積率的試驗數據，對相同壓力下不同噴嘴型號和相同噴嘴型號時壓力不同時的微粒化性能進行對比分析和研究，得到如下結論噴出量與霧錐形狀隨著壓力和噴嘴孔徑大小變化而變化；平均粒徑隨著壓力的增加和噴嘴孔徑的減小而明顯減小；粒數隨著壓力的增加和噴嘴孔徑的減小而明顯增多，為精噴量、低污染、高防效的防除作業奠定了實驗基礎。
  12. The flow field structure of the power - turbine variable - area nozzle stage of a marine gas turbine

    船用燃氣輪機動力渦輪可調導葉級的流場結構
  13. This thesis will put forward a new design project that aimed at discussing the packing sets of natural - draft counter - flow dry cooling tower, which is the research and application of the spray nozzle. the content mainly includes the experimental study of the application of the jnx - 01 spray nozzle in cooling tower, as well as the heating calculation

    本文將針對自然通風逆流濕冷式冷卻塔中影響效率較大的淋水裝置提出設計改進方案，即旋轉式噴濺裝置的研究與應用，內容主要包括jnx - 01型節能旋轉式噴濺裝置及旋轉濺水碟式噴頭在冷卻塔上應用情況的試驗研究及熱力計算。
  14. Although a dual - mode scramjet ' s configuration is simple and mainly consists of inlet, combustor and wake nozzle, its working process is complicated, especially in the combustor, involving a lot of subjects, including hypersonic aerodynamics, combustion chemistry, etc. the inner flow of a combustor is three - dimensional and complicated, including the interaction of shock wave, deflagration, vortex and boundary layer, and so on

    它涉及到高超聲速空氣動力學、燃燒化學、擴散傳質等多門學科；其內部的實際流動是復雜的三維流動過程，充滿著激波、膨脹波、燃燒波、各種渦系、附面層及其相互之間的干擾，因此，燃燒室問題是整個發動機研究的關鍵所在。
  15. （ detachable serrated nozzle, water flow control outlet attachable ）

    可拆卸水嘴，可加接防濺起泡器。
  16. The coupling from the pulse jet in the nozzle to the unsteady flow in the tube was discussed. and the relations between the parameters of gas charge and discharge, structure, working, flowing in tube and ideal cooling efficiency were established. the theory foundation of the influence of pulse jet on the flowing in the tube and characteristic would be built

    探討了脈動射流與管內非定常流動的耦合問題，建立了脈動射流有關參數如進、排氣參數、結構參數、運行參數等和振蕩管內流動參數及理想製冷效率之間的普遍聯系，為研究脈動射流參數對振蕩管內流動及其性能的影響打下了理論基礎。
  17. Optimise the melt flow, avoid dead zones in barrel, nozzle, hot runners

    優化流動，避免機筒，噴嘴和熱流道中的死區
  18. The impacts of different spray nozzle types and injecting pressures on temperature uniformity of the exhausted flow field of the gas generator were studied experimentally

    實驗研究了彩不同酒精噴入形成和參數對氣體發生器排氣溫度均勻性的影響。
  19. The polyamide to easy generation salivate ( pa ), through choosing form of a powerful person hot nozzle also can realize hot flow path to shape

    對易產生流涎的聚酰胺（ pa ） ，通過選用閥式熱噴嘴也能實現熱流道成型。
  20. Critical flow nozzle

    臨界流噴嘴
分享友人
分享到 Line

分享到臉書