fuel injection rate 中文意思是什麼

fuel injection rate 解釋
噴油率
  • fuel : n. 1. 燃料，柴炭。 ★指燃料種類時為可數名詞。2. 刺激物。vt. ,vi. （〈英國〉 -ll-）（給…）加[供給]燃料，（給船等）上煤，（給…）加油。-er 使用特製混合燃料的賽車。
  • injection : n. 1. 注射。2. 注射劑，注射液，針藥，灌腸（藥）。3. 充滿，注滿。4. 【醫學】充血。5. 【機械工程】噴射。6. 【宇宙空間技術】（衛星等的）入軌，射入軌道，射入軌道的時間[地點]。
  • rate : n 1 比率，率；速度，進度；程度；（鐘的快慢）差率。2 價格；行市，行情；估價，評價；費，費用，運費...
  1. The investigation has declared that the fuel injection with bq fuel pump had higher injection pressure, bigger fuel supply rate and shouter fuel supply duration, which would cause the fuel injection quantity and the fule - air mixture to increase during ignition delay period, the pre - mixed combustion to become acutely, and finally result in increased power levels of noise

    研究表明，裝配bq噴油泵，噴油系統的噴油壓力較高，供油速率較大和供油持續時間縮短，使得滯燃期的噴油量增加，滯燃期內形成的可燃混合較多，預混燃燒劇烈，導致整機噪聲聲功率級增加。
  2. A new calculation method for optimizing diesel engine performance, called nonlinear regression - mess method, is put forward. in this paper, 25 groups of simulated values are calculated from the diesel engine working model, specific fuel consumption, peak pressure, rate of pressure rise, nox and peak temperature are fitted into explicit function about compression ratio and fuel injection advance angle

    本文利用柴油機工作過程模型，得出25組模擬計算數據，利用非線性回歸將油耗、最大爆發壓力、壓力升高率、 no _ x濃度及最高燃燒溫度擬合成壓縮比和噴油提前角的顯函數，並用網格法進行優化，用c語言編制了優化計算程序，得出最佳的壓縮比和噴油提前角，使其優化匹配。
  3. A method based on the application of an injection process analysis software is introduced in this article, which optimize injection process through changing the design of fuel - injection pump cam. a model of 1115 single cylinder direct injection diesel engine is used as an example. with the help of pre - journey optimization, increasing cam lift and using tangent - function can make the matching of the injection system with the diesel more reasonable. without changing fuel pump installing size, it can enhance injection rate and injection pressure and improve the diesel operating stability in low speed condition

    本文以國產1115型單缸直噴柴油機為例，介紹一種應用噴油過程分析軟體改進噴油泵凸輪設計的方法，通過增大噴油泵凸輪升程、採用切線函數凸輪並優化預行程的方式，在不改變噴油泵安裝尺寸的前提下，可提高噴油壓力和噴油速率，改善柴油機低速工作穩定性，使噴油系統與柴油機匹配更合理。
  4. The injection fuel pump with 2. 5 mm diameter deliver pipe was analyzed and suitable for the power augmentation of tbd604b diesel according to the fuel injection pressure, fuel injection rate and duration of injection

    經計算分析p10型噴油泵配用2 . 5mm高壓油管，從噴油壓力、噴油速率、噴油持續期等參數來看，完全可以滿足提高功率后的tbd604b柴油機對燃油系統的要求。
  5. The 6psd30 - 1 fuel injection pump test stand is the 1970 ' s product and leave unused. its electrical control part is made up of large discrete components with low - test sensitivity, inconvenient setting and adjustment, high trouble rate. moreover, its circuit components are aging and spoiled

    6psd30 - 1型電子控制噴油泵試驗臺是七十年代的產品，其電氣控制部分電路採用大量分立元件構成，測試靈敏度低，設定調整不方便，故障率高，而且電路元件大多老化、損壞，現處于閑置狀態。
  6. At the conditions with the same fuel injection quantity per cycle and the same engine speed, with the increase of the additive mass fraction in the fuel, the ignition and heat release timings brought forward, the peak of heat release rate increased and the operating range at low engine load was enlarged obviously. however, excessive additives will make the engine be prone to knock, run rudely and shorten the operating range at high engine load

    在相同循環噴油量和相同轉速的條件下，隨著添加劑質量分數的增加， hcci著火和燃燒放熱提前，燃燒放熱峰值提高，低負荷工況范圍明顯拓寬，但過高的添加劑質量分數會使得發動機爆震，工作粗暴，導致高負荷工況變窄。
分享友人
分享到 Line

分享到臉書