fume emission 中文意思是什麼

fume emission 解釋
塵霧排放
  • fume : n 1 〈常 pl 〉煙氣；香氣，臭氣；熏煙；水蒸氣；煙霧。2 激昂，激怒。vt 1 （用煙）熏。2 烘製（木材等...
  • emission : n. 1. （光、熱、氣體等的）發出，發射，射出，放射；傳播。2. （紙幣等的）發行；發行額。3. 發出物，放射物。4. 【醫學】排出；遺精。
  1. Emission standard of cooking fume

    飲食業油煙排放標準
  2. Determination of emission rate of particulate fume in arc welding

    電弧焊接中微粒煙塵排放率的測定
  3. This paper introduced emission of cooking fume in shenyang, analyzed the polluted status, discussed the relative questions of monitoring and analysis method, and put forward the control method

    摘要結合實際監測數據介紹了沈陽市油煙排放狀況，對污染情況進行了分折，對油煙監測、分析方法中的相關問題進行了探討，提出了油煙污染控制對策及建議。
  4. There are 3 parts of heat loss for gas boiler, including heat emission loss, uncompleted burning loss and fume hot loss, uncompleted burning loss decreases following the increase of excess air coefficient, while fume hot loss increases. it is obvious that there exit an optimum coefficient of excess air which make boiler own highest efficiency which is the purpose of burning control

    不完全燃燒熱損失隨過量空氣系數的增大而減小，而排煙熱損失隨過量空氣系數的增大而增大，不難看出，存在一最佳的過量空氣系數使得兩者之和最小，即使得鍋爐的熱效率最高，燃燒控制的目的即在於此。
  5. Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - part 1 : determination of emission rate and sampling for analysis of particulate fume

    焊接和相關工藝的衛生與安全.電弧焊產生的煙塵和氣體取樣的試驗室方法.第1部分:顆粒煙塵排放率的測定和顆粒煙塵分析用取樣
  6. A concealed exhaust system equipped with high efficiency particulate air ( hepa ) filter was installed for the safety cabinets and the fume cupboards to reduce pollutant emission of the exhaust air by 99 %

    為減少化驗所排放的廢氣對空氣質素造成影響，化驗所安裝了一組密封式排氣系統，接連者安全罩櫃和排氣罩櫃。
  7. Laboratory method for measuring fume generation rates and total fume emission of welding and allied processes

    焊接和有關工藝中測量煙霧形成速度和總煙霧排放量的實驗室方法
  8. Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - determination of emission rates of gases, except ozone

    焊接和相關工藝的衛生和安全.電弧焊產生的煙和氣體取樣的實驗室法.除臭氧外的氣體排放率的測定
  9. Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - part 2 : determination of emission rates of gases, except ozone

    焊接和相關工藝中的衛生和安全.電弧焊產生的煙塵和氣體取樣的試驗室方法.第2部分:除臭氧外的氣體排放率測定
  10. Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - determination of emission rate and sampling for analysis of particulate fume

    焊接和有關加工工藝中的健康和安全性.電弧焊接產生的煙塵和氣體的實驗室取樣方法.排放率測定和顆粒煙塵分析的取樣
分享友人
分享到 Line

分享到臉書