furnace element 中文意思是什麼

furnace element 解釋
加熱元件
  • furnace : n. 1. 爐子；熔爐；高爐。2. 極熱的地方。3. 磨煉；艱難。vt. 在爐中燒熱（金屬）。
  • element : n 1 要素；成分；（構成）部分；分子。2 【化學】元素；【數學】元，素；【機械工程】單元；單體；【無...
  1. Using the opened thermosiphon of 38x3 as experimental element and water as working fluid, the characteristics of dynamic low load boiling, stable severe boiling heat transfer coefficient and critical heat flux are gotten for the opened thermosiphon at the pressure of 0. 02 - 0. 1mpa and 0. 1 - 0. 8mpa respectively, which makes up the drawback that the opened thermisiphon has not yet accurate boiling heat transfer relationship formulas. by means of experimental results, an opened thermisiphon waste heat recovery boiler is designed for the high temperature gases that the positi e electrode copper refining furnace exhaust, which overcomes effectively the drawback of short life, little capacity and unable to inspect that the closed steel - water thermosion has

    本文以工程上常用的38 3的開口封底為實驗元件，以水為工質，對開啟式熱管內的動態低負荷沸騰、穩態旺盛沸騰及臨界沸騰特性進行系統的可視化實驗研究，實驗壓力為0 . 02 0 . 8mpa ，實驗得出了38 3的開口封底管在工作壓力為0 . 02 0 . 8mpa和0 . 1 0 . 8mpa下的管內沸騰傳熱系數及臨界熱負荷計算關聯式，彌補了開口封底管? ?這一新型傳熱元件尚無準確的沸騰換熱關聯式的缺陷。
  2. The interface mechanical finite element matrix matching method and the thermal stress for the masonry envelop in the wall of melting furnace

    熔煉爐壁中砌體的界面力學有限元矩陣對號入座法與熱應力
  3. Wrkd - jz type thermocouple on the wall of boiler takes 4 sheathed thermocouple as measuring element. the thermal junction is fastened in stainless steel gathering heat clump with different curved surface of bearing treble points welded or m8 screw fixed to measure surface temperature of the wall of boiler, furnace and other equipments. wrkd - hg surface sandwich thermocoupleon the wall of boiler is specialized in measuring surface temperature of round column

    Wrkd - jz型鍋爐爐壁熱電偶採用4的鎧裝熱電偶做測溫元件，熱接點緊固在帶有不同曲面的不銹鋼，集熱塊上採用三點焊接或m8螺釘固定，用於鍋爐管壁，爐壁及其它設備的表面溫度。
  4. In order to search the demolishing effect pf the thermal stress on the hearth and bottom of the blast furnace, the distribution of temperature field and the thermal stress have been studied with the thermal elastic law and finite element method

    摘要為了探討熱應力對不同材質構成的高爐爐缸磚襯的破壞作用，在計算溫度場的基礎上，應用熱彈性理論和有限元法對高爐爐缸進行應力分佈計算。
  5. Standard practice for microwave digestion of industrial furnace feedstreams and waste for trace element analysis

    痕量元素分析用工業爐供入液流的微波溶解標準操作規范
  6. After determining the max furnace temperature, calculate the power ( kw ) of a single element using the way of multiplying the stipulated surface load of the elements under said furnace temperature ( find it out from the above table ) by the surface area of hot zone of the elements. ( find it out from the product dimension

    確定最高爐溫后，根據元件在此爐溫下所規定的表面負荷，乘以所選元件發熱部的表面積（從產品規格表中查出） ，求出單支元件的功率（ kw ） 。
  7. In this way, the entire plug and element assembly can be removed from the outside of the furnace

    這樣，這種硅碳棒和整個插栓可以在熔爐外進行安裝。
  8. The temperature is controllable and resultant and reductive process of nox can be simulated in furnace, which provide test element for nox reduction research with micronized coal reburning

    試驗爐內溫度可控制，可以模擬煤粉爐內nox的生成和還原過程，為超細粉再燃的研究提供了試驗基礎。
  9. “ when heated to incandescence in the furnace of stars, each element marks the spectrum of light it emits with a characteristic set of lines ” ( malcolm w. browne )

    「當在眾多星狀物組成的熔爐中被加熱到白熱程度時，每一個元素都以其特有的一組譜線顯示出它所放出的光譜」 （馬爾科姆w .布朗） 。
  10. 1. temperature measurement surface thermocouple with protective tube directly welded on the surface of furnace pipe to avoid scouring from extremely flow velocity and damage to measuring element at high temperature, also corrosion to the thermocouple from hydrogen and sulfur

    1 .一種帶護套管測溫表面熱電偶，護套管直接焊在爐管表面，避開了高流量沖刷，高溫溫度對測溫元件的破壞，氫硫對熱電偶的腐蝕
  11. When start to operate the furnace, raise voltage alowly and gradually, never give full load at one time, or the heating element will be damaged by over current impulse

    爐子在開始通電運行時，要逐步緩慢升壓，不可一次加滿負荷，否則會因沖擊電流過大造成元件損壞。
  12. Computer simulation of fluidized bed furnace caburizing concen tration field by non - linear finite element method

    剛玉流動粒子爐滲碳濃度場的非線性有限元法模擬
  13. The comparison made between simulation results and measured results, where the two results basically coincide with each other. it proves that the application of the distinct element method to blast furnace bell - less top charging is feasible which has also provided a new approach in theoretical study of bell - less top charging

    模擬與實測對比表明，兩者基本吻合，證明離散單元法在高爐無鐘布料應用中可行，並為高爐無鐘爐頂布料的機理研究開辟了一條新的途徑。
分享友人
分享到 Line

分享到臉書