furnace load 中文意思是什麼

furnace load 解釋
爐內負荷
  • furnace : n. 1. 爐子；熔爐；高爐。2. 極熱的地方。3. 磨煉；艱難。vt. 在爐中燒熱（金屬）。
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  1. When specifying the transformer, the nominal full load voltage is usually reduced to allow for the minus 20 % resistance tolerance of the elements and slow furnace heatup

    當指定變壓器時，考慮到要減去20 %的電阻阻值，通常要減少額定滿負電壓並且使熔爐加熱緩慢。
  2. The key products of the company are high alumina brick, fireclay brick, phosphate - bonded wearable brick, exfoliation - resistant high alumina brick, high refractoriness under load brick, corundum brick, magnesite brick, magnesite ? chrome brick, series of corundum, sic furnace chamber and pipe, ceramisite brick, corundum - mullite brick, corundum - chrome brick, sillimanite brick, magnesite alumina spinel brick, acid - resistant brick, alkali - resistant brick, zirconia - corundum brick, alumina bubble products, series thermal insulating refractory products, high alumina castable, corundum castable, corundum ramming, brown - corundunm castable, sic castable, low - cement castable, alkali ? resistant castable, light silica alumina products, stainless steel fibre reinforced castable, etc

    主要產品有：高鋁質磚、粘土質磚、磷酸鹽耐磨磚、抗剝落磚、高荷軟磚、剛玉磚、碳化硅磚、鎂磚、鎂鉻磚、各種剛玉、 sic爐膛、爐管製品、陶粒磚、剛玉莫來石磚、鉻剛玉磚、硅線石磚、鎂鉻尖晶石磚、耐酸磚、耐堿磚、鋯剛玉磚、氧化鋁空心球製品及各種輕質保溫材料、高鋁質澆注料和剛玉澆注料、搗打料、棕剛玉澆注料、碳化硅澆注料，低水泥澆注料、抗堿性澆注料、輕質硅酸鋁製品、鋼纖維增強澆注料等80餘種系列耐火材料。
  3. Using the opened thermosiphon of 38x3 as experimental element and water as working fluid, the characteristics of dynamic low load boiling, stable severe boiling heat transfer coefficient and critical heat flux are gotten for the opened thermosiphon at the pressure of 0. 02 - 0. 1mpa and 0. 1 - 0. 8mpa respectively, which makes up the drawback that the opened thermisiphon has not yet accurate boiling heat transfer relationship formulas. by means of experimental results, an opened thermisiphon waste heat recovery boiler is designed for the high temperature gases that the positi e electrode copper refining furnace exhaust, which overcomes effectively the drawback of short life, little capacity and unable to inspect that the closed steel - water thermosion has

    本文以工程上常用的38 3的開口封底為實驗元件，以水為工質，對開啟式熱管內的動態低負荷沸騰、穩態旺盛沸騰及臨界沸騰特性進行系統的可視化實驗研究，實驗壓力為0 . 02 0 . 8mpa ，實驗得出了38 3的開口封底管在工作壓力為0 . 02 0 . 8mpa和0 . 1 0 . 8mpa下的管內沸騰傳熱系數及臨界熱負荷計算關聯式，彌補了開口封底管? ?這一新型傳熱元件尚無準確的沸騰換熱關聯式的缺陷。
  4. Under the load of high basicity occur three circular crevices from top to bottom at the furnace hearth parallel to the furnace shell

    在高堿度負荷下，該高爐爐缸部位產生了平行於爐殼的至上而下的三條環裂。
  5. The electric heat components and heated components in resistor furnace were regarded as research object, the simplified model was provided on the basis of simplification of studied objects, the thermotechnical theoretical calculation and analysis for it were done by utilizing radiation heat transfer theory, some main factors influencing the temperature of electric heat component were obtained on condition that the hot load for the heated component be constant, thermotechnical engineering scheme by which the service life for resistor component could be prolonged, was raised

    摘要以電阻爐中的電熱元件和被加熱元件為研究對象，經過簡化提出簡化模型，運用輻射換熱理論對其進行了熱工方面的理論計算和分析，在被加熱元件熱負荷一定的情況下，得出了影響電熱元件溫度的幾大要點，提出了延長電熱元件使用壽命的熱工技術方案。
  6. Suilable for low load position, wear performance worsens greatly when under middle or high load. can be applied in furnace door lindge, furnace, conveyor, tool machines, light industries, etc

    51主要適應低載高溫中速的使用場合，例如壁爐門鉸鏈、烘爐滾道、輕工機械、機床工業等。
  7. Analysis about influence factors on heat load of blast furnace wall

    影響高爐爐墻熱負荷的因素分析
  8. By the industrial experiment, the distribution of continuous casting billet preheating temperature is measured, and the economic load range of reheating furnace is established

    摘要在工業生?條件下測量了鑄坯加熱溫度分佈，工業試驗確定了加熱爐經濟負荷運行區。
  9. After determining the max furnace temperature, calculate the power ( kw ) of a single element using the way of multiplying the stipulated surface load of the elements under said furnace temperature ( find it out from the above table ) by the surface area of hot zone of the elements. ( find it out from the product dimension

    確定最高爐溫后，根據元件在此爐溫下所規定的表面負荷，乘以所選元件發熱部的表面積（從產品規格表中查出） ，求出單支元件的功率（ kw ） 。
  10. Load test furnace

    載重擁驗爐
  11. Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  12. The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  13. On the other hand, because of the fluctuating load, such as arc furnace and railway traction locomotive, the voltage of the network will frequently fluctuate and lead to voltage flash

    另一方面，現代配電網上用於冶煉的電弧爐和鐵路牽引機車等波動性負荷，會使電網電壓頻繁波動，造成電壓閃變。
  14. And the conclusion is that downing load can distory the small slag and outer part of thick slag, which is helpful to keep walltube clean and useless for preventing from furnace accident caused by slag

    鍋爐降負荷運行有一定程度清潔爐膛水冷壁作用，能增強爐內傳熱，卻無法防止爐膛內結渣惡化發生嚴重事故。
  15. Based on the advanced technology and instruments of visible monitoring system of section temperature field in furnace, energy saving & environmental protection test vehicle and 3 - dimension furnace computational simulation, test and study are carried out on stability of peak - load regulation and optimization of operation of large unit

    摘要利用爐膛斷面溫度場可視化監測系統、節能環保車、爐內三維數值模擬等先進的技術和設備對大機組調峰穩定性和運行方式優化進行試驗和理論研究。
  16. Corundum mullite product adoprs electrocast refractories. through high pressure formation and high temperature burning, this product has comparatively high refractoriness, mechanical strength and slftening temperature under load. it can be widely used as inner lining. of various industrial furnace under such hard working conditions as high temperature, flushing and erosion

    剛玉莫來石製品是採用電熔合成原料，高壓成型，高溫燒成的具有較高耐火度及機械強度，較高荷重軟化濁的可廣泛應用於各類工業爐高溫、沖刷、侵蝕條件較苛刻的窯爐內襯的耐火製品。
  17. For ac electric arc furnace is an unbalanced, nonlinear and time variant load that produces unbalance, harmonics and interharmonics related with flicker effect. the modeling of all these aspects requires adopting a nonlinear, asymmetrical and dynamic v - i characteristic for the electric arc

    由於交流電弧爐是一種不平衡的、非線性時變負載，它產生與電壓閃變有關的不平衡、諧波和分數諧波，所有這些就需要一種非線性、不對稱的動態u ? i特性的電弧爐模型。
  18. Abstract : the on line measuring technology suitable for closed cooling system as well as open cooling sysem of blast furnace in the water temperature, the difference in water temperature, the rate of flow, the current velocity, the heat load and lead water detection is introduced. the fundamental principles and requirements involved and distributed computer network applied in the measuring system are described. the situations in industrial use are analyzed and summed up

    文摘:詳細介紹了一種既適用於高爐閉路冷卻系統，又適用於高爐開路冷卻系統的進出水溫度、水溫差、流量、流速、熱負荷及檢漏在線監測技術.描述了該技術基於的基本原理和要求以及檢測系統所採用的分步式計算機網路結構特點.最後，對該技術的工業實際應用情況進行了分析和總結
  19. Meanwhile some detailed researches are done on the deviation of gas in different load in tangentially - fired furnace which affords some significant directions in theory on the boiler ' s safely operation. simple method is employed in flow field prediction ; lagrangian method is used in the flow of particle and the radiant heat - transfer is simulated in monte carlo method. through summarizing these methods, the author develops a general program of large - scale power station with a friendly interface and post - disposal

    本文對模擬爐內過程所採用的方法和模型進行了概括和總結，在此基礎上綜合這些方法和模型，如流場的計算採用的是simple方法，而顆粒相流動則是採用拉格朗日方法進行研究，輻射換熱採用蒙特卡洛方法等，並且以這些模型和方法為基礎，開發了大型電站鍋爐的通用程序，並包括友好的界面和后處理。
  20. When start to operate the furnace, raise voltage alowly and gradually, never give full load at one time, or the heating element will be damaged by over current impulse

    爐子在開始通電運行時，要逐步緩慢升壓，不可一次加滿負荷，否則會因沖擊電流過大造成元件損壞。
分享友人
分享到 Line

分享到臉書