gap shear 中文意思是什麼

gap shear 解釋
開式剪切機
  • gap : n 1 （墻壁、籬笆等的）裂口，裂縫；豁口，缺口。 【軍事】突破口。2 （意見的）齟齬，分歧；隔閡，距離...
  • shear : vt vi （sheared 〈古語〉 shore; shorn sheared）1 剪（羊毛等）；修剪（樹木）；剪（呢絨的）長毛。2 ...
  1. Standard test method for determining strength of gap - filling adhesive bonds in shear by compression loading

    測定裂縫強度的標準試驗方法.用壓力負荷法測定填充膠粘劑的剪切粘結強度
  2. Abstract : the flying shear located behind the roughing stands of wire - rod mill is designed with hard surface gears for driving system, engaging of zero tolerance, hydraulic cylinder for clamping and shiftting, convenient and practical gap adjusting structure for blade

    文摘:介紹了邯鋼三軋廠在線材軋機粗軋機組后的飛剪設計中，採用了硬齒面齒輪傳動，零側隙嚙合，液壓缸鎖緊與橫移及簡便實用的剪刃間隙調整機構。
  3. After the length of the gap increasing to a certain value the load bearing ability and actual shear strength intends to decrease

    研究中還發現間隙所處的位置對接頭的抗剪強度有較大的影響，膠層端部預留間隙使接頭的承載能力和實際強度均顯著下降。
  4. The way that two kinds of different potentiometer feeding back the blade gap value in adjusting mechanism of cnc shear have been introduced

    摘要介紹了數控剪板機刀片間隙自動調整機構中兩種不同電位器反饋刀片間隙值的方式。
  5. The author advances that the shear connector is simulated by two spring elements, which are vertical to each other and parallel to the interface between steel and concrete, and one multipoint constraint element, mpc element, which is vertical to the interface. the author also puts forward that the crack of the deck is simulated by the gap element which ca n ' t support longitudinal tensile force but can support longitudinal compressive force

    提出了以正交的兩個平行於鋼和混凝土界面的彈簧單元及一個垂直於界面的多點約束（ mpc ）單元來模擬剪力鍵，以小間隙接觸（ gap ）單元來模擬混凝土橋面板的開裂，模型中忽略了混凝土板與鋼梁接觸面間由摩阻而產生的粘著力。
  6. If the gap between two branch members is great, the joint is treated as t - or y - joint. or else, the minimum of the results obtained by the formula based upon steel tube flange shear failure mode and effective width failure mode is adapted for the tension branch joints

    給出了矩形鋼管混凝土k型節點的間隙判斷公式，間隙較大時按t 、 y型節點計算；間隙較小時受拉支管節點承載力按沖剪破壞和有效寬度破壞模式計算，取較小值。
  7. Testing of soldering joints ; gap soldered joints, shear test, creep shear test

    釬焊接頭檢驗.接縫釬焊接頭剪切試驗蠕變剪切試驗
  8. Results from the experiment show that the load bearing ability of the single - lap joint decreases as the length of the gap increase but the actual shear strength is increased in same time

    結果表明，隨著間隙長度的增加，接頭的承載能力趨于減小，但接頭的實際剪切強度卻持續上升；當間隙長度繼續增加時，接頭的實際強度趨于下降。
  9. Or else, the minimum of the results obtained by the formula based upon steel tube flange shear failure mode and effective width failure mode is adapted. 3 ) the gap judging formula for k - cfrst joints is provided

    T 、 y 、 x型受拉節點支主管寬度比0 . 7時，按屈服線破壞模式計算； 70 . 7按沖剪破壞和有效寬度破壞模式計算，取較小值。
分享友人
分享到 Line

分享到臉書