gear pair 中文意思是什麼

gear pair 解釋
齒輪副
  • gear : n 1 【機械工程】齒輪，（齒輪）傳動裝置，齒鏈；排擋。2 〈古語〉衣服；甲胄與武器。3 傢具；財物，動...
  • pair : n （pl pair（s））1 一對，一雙，一套，（眼鏡等的）一副；（剪子等的）一把，（褲子等的）一條。 2 一...
  1. Hypoid gear pair

    準雙曲面齒輪副
  2. The maker of athletic gear lost 45, 756 shoes - or 22, 878 pair - that fell off a storm - tossed container ship in december on the way from long beach, california, to tacoma, washington

    去年十二月，由於遭遇暴風雨，這家運動產品生產大戶在從加利福尼亞長灘到華盛頓塔科馬的運貨途中丟了一隻裝有22878雙，也就是45756隻運動鞋的集裝箱。
  3. Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center, considering all influential elements, the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision

    摘要根據換向傳動齒輪副從上止點向下止點運動時被動齒輪運動超前的實際，從影響齒輪副側隙的各種因素出發，在不提高齒輪副製造精度的前提下，通過拉制齒輪副公法線長度及其偏差從而有效地控制齒輪副的最大齒側間隙，以滿足傳動的特殊要求。
  4. The application of internal gear pair with modified centre distance

    內嚙合變位齒輪傳動的應用
  5. This paper develops a mathematical model for the solution to the longitudinal tooth curve of an internal gear shaver based on the simplified principle for space transmission of a helical gear pair without flank clearance, and proposes a calculating approach of the profile modification of the grinding wheel to be used for grinding the longitudinal tooth curve of the shaver

    摘要用簡化的空間螺旋齒輪作無側隙嚙合傳動的原理，建立了求解內剃齒刀齒向曲線的數學模型，並給出了修磨這種齒向曲線的盤形砂輪的廓形計算方法。
  6. Gear pair with intersecting axles

    相交軸齒輪副
  7. The establishment of gear fault data warehouse the paper studies several gear cases in drive lab of wuhan university of science and technology. the signal of normal gear pair, the one has been worn seriously, the one which has circular pitch error and the one whose pinion has a ruptured tooth is acquired independently. after fft transformation, the amplitude values of 0 - 0. 4 multiple engage frequency, 0. 4 - 0. 5 multiple engage frequency, 0. 5 - 1 multiple engage frequency, 1 multiple engage frequency, 2 multiple engage frequency, 3 multiple engage frequency, 4 multiple engage frequency and greater then 4 multiple engage frequency of every signal are obtained respectively

    論文主要完成下列內容: 1 .齒輪故障數據倉庫的建立以武漢科技大學傳動實驗室的若干臺齒輪箱為研究對象，分別採集正常齒輪副、磨損嚴重的齒輪副、有周節誤差的齒輪副和小齒輪有一個斷齒的齒輪副的振動加速度信號，經過fft變換，分別得到每個信號的0 ~ 0 . 4倍嚙合頻率、 0 . 4 ~ 0 . 5倍嚙合頻率、 0 . 5 ~ 1倍嚙合頻率、 1倍嚙合頻率、 2倍嚙合頻率、 3倍嚙合頻率、 4倍嚙合頻率和大於4倍嚙合頻率幅值。
  8. Furthermore, we carry out motion simulation to the spherical gear, gear ' sfluted disc and flexible wrist, thus confirm the theoretical analysing model. 5. we bring forward the generating cutting method based on spherical gear drive, and develop experimental cutting set - up in principle. in theory, the generating mehtod bases that the tooth form of a pair of gear is conjugated

    范成法加工的理論依據在於一對球齒輪的齒廓曲面互為共扼曲面，它們在傳動過程中互為包絡面，如果將其中的一個球齒輪的齒廓做成刀具，另一個為被加工齒輪的毛坯，由機床傳動系統保證兩者之間的嚙合運動，就可以加工出球齒輪。
  9. The special purpose is for inspecting the position and noise of meshing section of quadrature taper pair, according to the inspecting result, this machine will guide milling gear machine to make a adjustment and begin to cut teeth again, finally, to satisfy the mesh request of taper gear pair

    本機床專用於檢查正交錐齒輪副的嚙合傳動噪聲，並可根據檢查的結果，指導銑齒機的調整和重新切齒，最終達到錐齒輪副的嚙合要求。
  10. Based on the tribology theory, the experiment method of the scuffing load capacity of worm gear oil was studied in this paper by means of the large number of groping evaluation experiments, and based on the test results of worm gear drive lubricated by 15 types oils and the surface analysis of worm gear after the experiments, the effect of oils and additives on anti - scuffing load capacity of worm gear pair was studied. the results show that the experimental method of the scuffing load capacity of worm gear oil has a good repeatability and distinguishability

    本文運用摩擦學理論，通過進行大量的臺架評定探索性試驗，研究開發出蝸輪蝸桿油膠合承載能力臺架評定試驗方法，並在此基礎上進行15種不同配方的蝸輪蝸桿油的膠合承載能力臺架評定試驗和試驗后蝸輪齒面的表面能譜分析，以考察潤滑油、添加劑對蝸桿傳動膠合承載能力的影響結果。
  11. Aimed to the two deficiencies of three - ring gear transmission, the dissertation will analyze these two aspects. the first, according to the finite element model of gear pair of three - ring gear reducer, the dissertation is aimed to analyze the multi - tooth meshing effect of three - ring gear reducer using finite element method, and the number of teeth contacted simultaneously, their load distribution characteristics and the von mises stress change are gained

    針對三環減速器以上兩點的不足之處，本文將對以下兩方面進行分析:首先，本文以三環減速器齒輪副有限元模型為研究對象，利用有限單元法對三環減速器多齒嚙合效應進行分析，得到三環減速器傳動時的實際接觸齒數、嚙合齒載荷分配以及vonmises應力變化規律。
  12. Gear pair with parallel axes

    平行軸齒輪副
  13. Bevel gear pair

    錐齒輪副
  14. Compare the results of two methods of non - linear vibration of a spur gear pair

    直齒輪副非線性振動分析中兩種解法的結果比較
  15. Experimental research for gear pair lubricating oil film thickness

    齒輪副潤滑油膜厚度的實驗研究
  16. A gear pair model and its application in the software adams

    一種齒輪副模型及其在多體動力學模擬中的應用
  17. 3 、 based on the model, a quasi - static meshing simulation is carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs. the different meshing position are presented, and the rationality of the model is be verified

    3 、基於所建有限元分析模型，在一個嚙合周期內，對齒輪副進行準靜態嚙合模擬分析，給出了準靜態嚙合時齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩和轉速隨嚙合位置變化的規律，驗證了所建模型的正確性。
  18. 4 、 on the basis of analyse of a quasi - static meshing simulation in a meshing period, a dynamic meshing simulation in the case of definite torque and rotary speed are carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs the different meshing position are presented

    4 、在對螺旋錐齒輪準靜態嚙合進行模擬分析的基礎上，進行了螺旋錐齒輪動態瞬態嚙合模擬分析，重點分析帶載啟動時出現的沖擊現象，得出了齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩、轉速和加速度隨嚙合位置變化的規律。
  19. Kinematic characteristics and gear pair design for deformed elliptical geared linkage mechanism

    變性橢圓齒輪連桿機構的運動特性及齒輪副設計
  20. Gear pair with non - parallel

    交錯軸齒輪副
分享友人
分享到 Line

分享到臉書