gear pinion 中文意思是什麼

gear pinion 解釋
主動齒輪, 小齒輪
  • gear : n 1 【機械工程】齒輪，（齒輪）傳動裝置，齒鏈；排擋。2 〈古語〉衣服；甲胄與武器。3 傢具；財物，動...
  • pinion : n 1 （鳥翼的）翼梢；翅膀；羽毛；〈集合詞〉翮；〈詩〉翼。2 （人的）臂膀；臂綁。vt 1 剪斷…的翮毛，...
  1. The gearing machine tool of the model y3150e is modified and a new milling head is designed to cut the envelope tooth of the pinion using allelomorph method. a assembled drawing of clamp for cutting the tooth shape of circle - arc gear is also presented

    對y3150e型滾齒機進行改造，設計出一新型的銑削頭，利用對偶法加工小齒輪的圓弧包絡線齒形；同時也給出了加工大齒輪圓弧齒形的夾具裝配圖。
  2. Pinion - type cutters for cylindrical gears ; disc - gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用盤形齒輪銑刀
  3. Pinion - type cutters for cylindrical gears ; shank - gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用帶柄齒輪刀具
  4. Pinion - type cutters for cylindrical gears ; extended hub gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用加大轂形齒輪刀具
  5. Geometrical design of cylindrical internal involute gear pairs ; diagrams for limits of internal gear - pinion type cutter matings

    漸開線嚙合圓柱內齒輪副的幾何設計.內小齒輪刀具配合
  6. Drive pinion gear depth

    驅動齒輪深度
  7. Check the gear wheel drive in the groove of the wall, select four gear wheel ( red pinion is not used ) of different size for use, load heavy gear wheel, times of heavy gear wheel, times of light gear wheel, minimum gear wheel most onto separately from left to right, make gear wheel hand in, form each other, leave behind, operate a switch, drive, finish

    檢查墻壁凹槽中的齒輪驅動裝置，選用大小不同的四個齒輪（紅色的小齒輪不用） ，從左到右分別裝上最大的齒輪、次大的齒輪、次小的齒輪、最小的齒輪，並使齒輪間相互交結，拉下拉閘，驅動完成。
  8. Geometrical design of cylindrical internal involute gear pairs ; diagrams for geometrical limits of internal gear - pinion matings

    漸開線嚙合圓柱內齒輪副的幾何設計:內小齒輪配合的幾
  9. The large machined main gear and standard 15 tooth pinion gear comprise the rotor head drive system on the synergy n9

    大型機械齒輪、標準主要包括1915年牙杯頭插齒傳動系統的協同n9號
  10. The establishment of gear fault data warehouse the paper studies several gear cases in drive lab of wuhan university of science and technology. the signal of normal gear pair, the one has been worn seriously, the one which has circular pitch error and the one whose pinion has a ruptured tooth is acquired independently. after fft transformation, the amplitude values of 0 - 0. 4 multiple engage frequency, 0. 4 - 0. 5 multiple engage frequency, 0. 5 - 1 multiple engage frequency, 1 multiple engage frequency, 2 multiple engage frequency, 3 multiple engage frequency, 4 multiple engage frequency and greater then 4 multiple engage frequency of every signal are obtained respectively

    論文主要完成下列內容: 1 .齒輪故障數據倉庫的建立以武漢科技大學傳動實驗室的若干臺齒輪箱為研究對象，分別採集正常齒輪副、磨損嚴重的齒輪副、有周節誤差的齒輪副和小齒輪有一個斷齒的齒輪副的振動加速度信號，經過fft變換，分別得到每個信號的0 ~ 0 . 4倍嚙合頻率、 0 . 4 ~ 0 . 5倍嚙合頻率、 0 . 5 ~ 1倍嚙合頻率、 1倍嚙合頻率、 2倍嚙合頻率、 3倍嚙合頻率、 4倍嚙合頻率和大於4倍嚙合頻率幅值。
  11. Rack and pinion steering gear

    齒輪齒條式轉向器
  12. Bevel pinion and bevel gear set

    主動小錐齒輪和被動大錐齒輪副
  13. It has many advanced equipments, such as driving axle spiral bevel gears processing lines from gleason company and the ring gear & pinion producing machines from mitsubishi company

    工廠生產設備先進，擁有美國格里森后橋螺旋傘齒輪加工線和日本三菱公司圓柱齒輪加工設備。
  14. After synthetically studying the effects of loading positions, rim thickness, circular pinion numbers and fillet radii of gear hob on root section stresses, a judging formula of plane stress and plane strain is proposed and verified, then 2d and 3d fem models are accurately established

    系統探討了加載位置、輪緣厚度、周向齒數的確定方法，分析了滾刀頂部圓角對齒根應力的影響，提出了兩類平面問題的判據並予以驗證。
  15. The pinion gear is on the same shaft as the motor armature and rotates at the same speed

    小齒輪如馬達電樞般在同一曲軸上，且以相同的速度轉動。 ？
  16. When the shaft is rotated, the pinion with the same axle remains stationary, driven in the opposite direction by another gear

    當軸轉動時，同軸心的小齒輪不動，由另一個齒輪帶動它往反方向轉動。
  17. Load of gear box can be decided by measuring of low speed shaft contort. in mill system of single - pinion drives

    邊緣傳動磨機系統，可以通過實測低速軸的扭矩來確定系統中減速機的負載狀況。
  18. It is important rules that research for dynamic characteristics of the mill system of single - pinion drives in operation to prevent damage from the resonance between fix frequency and bestir frequency in this paper, the pattern of pinion - - - drive shaft - - - decelerator gear vertical vibration in the mill system of single - pinion drives is established

    最後，對2 . 6 13m的磨機系統進行了動態特性的實例分析。研究邊緣傳動磨機系統的動態特性，對避免由於激勵頻率接近或等於系統的固有頻率而導致共振及設備的失效，預測系統在可能激勵下的響應特性，優化系統結構等等都具有很重要的意義。
分享友人
分享到 Line

分享到臉書