gear tooth engagement 中文意思是什麼

gear tooth engagement 解釋
齒輪齒嚙合
  • gear : n 1 【機械工程】齒輪，（齒輪）傳動裝置，齒鏈；排擋。2 〈古語〉衣服；甲胄與武器。3 傢具；財物，動...
  • tooth : n （pl teeth）1 牙齒。2 齒狀突出，輪齒，鋸齒，耙齒（等）。3 嗜好。4 〈常 pl 〉（像牙齒那樣能咬人...
  • engagement : n. 1. 約會，約定；約束，契約；預約。2. 婚約。3. 僱用，聘用期；職業。4. 義務；〈pl. 〉債務。5. 【軍事】戰斗。6. 【機械工程】接合，咬合。
  1. Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters

    對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。
  2. One of tooth profiles of coarse - pitch gear ball hob is analyzed in engagement theory ， the tooth profiles of the internal gear has been derived. by comparing the tooth profile with the tooth profile of the standard internal gear, it is shown that the tooth profile is satisfying

    對大模數內齒輪球形滾刀的一種齒形進行嚙合理論分析，求出滾刀加工出來內齒輪的齒形，然後與標準內齒輪的齒形比較，結果表明：該齒形的滾刀加工的內齒輪能滿足要求。
  3. Based on the theories of gear engagement, contact analysis, friction and heat transfer, a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions. sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated

    本文基於齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學，以有限元分析方法和理論分析計算相結合為手段並以實驗測量結果作為參考，建立了適用於工業應用並具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法，系統地分析了輪齒本體溫度的大小和分佈以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。
分享友人
分享到 Line

分享到臉書