geometric diameter 中文意思是什麼
geometric diameter
解釋
幾何學粒子徑-
Geometric mean diameter
幾何平均直徑 -
Based on this model, the effects of geometric and structural parameters, such as injection pressure, rear pressure, length - diameter ratio, inlet round angle - radius ratio and non - axis symmetry of nozzle, on the distribution of the cavitation inside the nozzle are analyzed
基於這一模型進一步分析了噴射壓力、背壓和噴孔長徑比、噴孔入口圓角比、非軸對稱噴孔等幾何結構參數對噴孔內空穴分佈的影響。 -
Soil particle - size distributions fractal dimension is correlative with other texture parameters. the dimension is clear line - relative with clay content and geometric mean diameter, but the line - relationship between the dimension and index of uniformity is low. the dp is sensitive to the variety of soil texture
在理論上也進一步指明了粒徑分佈維數的物理意義，即：粒徑分佈分形維數d _ p的范圍為0 3 ，其大小反映了不同質地土壤顆粒的填充能力。 -
An experimental study is carried out on the effect of following factors on the combustion performance of a vehicle fuel heater : geometric parameters ( the number, diameter, distribution and direction of combustion chamber intake holes ) and intake and exhaust pressures
摘要對車用燃油加熱器燃燒室進氣孔徑（流通面積） 、孔的分佈、孔的方向等幾何參數和進排氣壓力對加熱器燃燒性能的影響進行了試驗研究。 -
Laser - scanned measuring for the diameter system involved optics, laser, electronics, computer and mechanics etc, in the system, a visible laser is taken as its light source, the geometric parameter of the measured object is transformed into the electrical sighals by a scanning optical system and an opto - electronic transformation system, the measured result is given and displayed by the computer real time data processing
激光掃描測徑儀系統是一種基於光學技術、現代激光、電子學、計算機、精密機械等多學科技術於一體在線檢測系統。它是用可見激光作為光源，把被測對象的幾何尺寸經過掃描光學系統和光電變換系統轉變成電信號，再由計算機進行實時數據處理，給出測量結果，並數字顯示。 -
Based on the analysis about the test requirements and the saturated magnetization of the armor plate, the excitation magnetic circuit satisfying the testing condition and a validation system are designed. because the geometric, of the magnetic leakage at the direction of the normal of the roundness fault has the feature of two peaks : a positive and a negative, using the linear regression and the software matlab, two regression equation are proposed : one is about the peak value of the magnetic leakage and the diameter and depth of the roundness fault ; the other is the distance between the two peaks and the diameter of the roundness fault. the result of the validation system proves that the two equations are valid, and an applied method using for quantificationally inspecting the roundness faults is proposed according to the two equations
根據實驗要求，通過對鋼板達到飽和磁化的必要性進行的分析，設計了符合試驗條件的勵磁磁路，並設計了一套實驗驗證系統；根據圓形缺陷法線分量漏磁場幾何圖形正負雙峰值的特點，採用線性回歸擬合的原理和matlab軟體及其統計工具箱中的相關函數，給出了圓形缺陷漏磁場幾何圖形的峰峰值與圓形缺陷的直徑和深度以及峰峰值間距與圓形缺陷直徑的兩個回歸擬合方程，並通過實驗驗證系統驗證了擬合方程的正確性，利用這兩個簡單實用的擬合方程，提出了一種工程定量檢測圓形缺陷的應用方案。 -
The results showed that the processing parameters ( such as laser power, the diameter of laser, scanning speed of laser beam, ratio of overlapping ) are important to acquire a perfect component. furthermore, in order to assure geometric properties ( accuracy, surface finish ), the structure of the off - axial powder nozzle was improved to avoid the oxidation of the molten pool. the density metal test sample of rene95 high - temperature alloy was made by lsf through optimizing the processing parameters
本文對激光立體成形的工藝特性進行了深入系統的研究，發現如果要獲得理想的成形效果，就必須對成形過程中的工藝參數進行精密控制，例如激光功率、激光光斑大小、光束掃描速度、搭接率等；同時為了保證成形件有較高的尺寸精度和表面質量，必須對成形零件的氧化問題進行控制，通過改進側向送粉噴嘴的結構設計，成形件的表面氧化問題得到適度控制。 -
The paper indicates that the study on mechanism of boiling heat transfer in microchannels does not first - orderly instruct engineering design and appliance, and they are constraints between geometric dimension, passage diameter, number and length efficiency of evaporators, pump power and so on
指出對于微通道沸騰換熱的傳熱機理等的研究對工程設計和應用來講還沒有形成合適的技術指導依據，蒸發器尺寸、通道直徑、數目、通道長度、換熱效率以及泵功率之間是相互制約的。 -
We designed two kinds of diameter s - shaped curved arteries finite element numerical simulation geometric models in order to study the influence caused by the singular curved factor ( such as the curvature radius, the dean number ) to flow, and extract the characteristic flow form related to the curve
在總結和發展前人成果的基礎上，設計了兩種直徑的s型彎曲動脈有限元數值模擬幾何模型，以考察單一的彎曲因素（曲率半徑、 dean數等）對流動的影響，以提取與彎曲相應的特徵流型。
分享友人