girder mill 中文意思是什麼
girder mill
解釋
鋼梁軋機-
And it investigates the appearance condition ( including joint, crack, eroding, corrosion, braking pole device rupture, crane - girder ' s gnawing railway and so on ) of the whole crane - girder system on the spot, at the same time, it also actually examines the stress of the beam, chemical ingredient, distortion and railway excursion, etc. through sampling, and based on the actually examined results, it checks and calculates the carrying capacity of crane - girder system. then, based on the investigating on the spot and the calculated result, it discusses the mechanism of fatigue failure of the upper part of welded steel crane - girder, analyses the reason of steel crane - girder in the high - frequency emerging the fatigue crack, institutes the strengthened method of damaged steel crane - girder of accurate packing up workshop of the primary mill plant. finally, it presents some advice and suggestions for the repairing and strengthening method of fatigue crack of upper part of steel crane - girder in the high - frequency
針對包鋼初軋廠精整車間鋼吊車樑上部區域出現裂縫這一問題，本文首先綜述了國內外關于焊接鋼吊車樑上部區域疲勞裂縫的研究現狀；其次對整個吊車梁系統的外觀情況（包括連接、裂縫、腐蝕、銹蝕、制動桿件斷裂、吊車啃軌等）進行了現場調查，抽樣實測了梁的應力、化學成分、變形及軌道偏移等，根據實測結果，對吊車梁系統的承載能力進行了驗算；然後，根據現場調查及計算結果，探討了焊接鋼吊車樑上部區域疲勞破壞的機理，分析了重級工作制鋼吊車梁出現疲勞裂縫的原因，制定了初軋廠精整車間破損鋼吊車梁的加固方案；最後就重級工作制鋼吊車樑上部區域出現疲勞裂縫的修復與加固方案提出了一些意見和建議。 -
Based on practical project of inspecting, appraising and reinforcing a main heavy factory building, especially its steel crane girder system, of the second steel mill belonging to taiyuan steel & iron corporation, whose technology renovation leads to increase tonnage of many heavy cranes and vertical load of frame - bent structure, first the structure and its members were investigated, inspected, calculated and analyzed, and their reliability was appraised respectively and the strengthening projects or the measures to remedy were given. then, in accordance with the requirement to strengthen the girders under non - stop production, the feasibility of strengthening the crane girders by adding steel diagonal braces underneath the existing girders has been studied by inspecting and evaluating the strengthening effect of the crane girders and comparing with other reinforcing scheme
本文結合太鋼（集團）有限公司第二煉鋼廠主廠房由於生產工藝改造要求，加大多臺重型吊車噸位及bc跨（ 1 ） （ 8 ）軸線框排架各層豎向（設備）荷載后，對廠房結構，尤其鋼吊車梁系統進行檢測鑒定與加固設計的實際工程，首先對廠房結構進行了現場調研、技術檢查、測試以及內力和承載能力的計算與分析（考慮抗震） ，並根據檢測、計算與分析結果，對廠房結構、構件的可靠性進行了評定，並綜合提出鑒定結論和加固處理建議。 -
In order to be more typical and practical, the theses pays more attention to analyzing the quality control of the rail - girder factory of panzhihua steel - iron company. the factory is a highly automatic and mechanized heavy rolling mill. it has been practicing a relatively effective quality control for about 20 years
為使文章更具代表性和實用性，本文著重分析了攀鋼軌梁廠的質量控制，攀鋼軌梁廠作為一家機械化、自動化程度較高的大型軋鋼廠其質量控制工作已經開展了20多年，應該說是比較成熟的。 -
The overhead traveling crane used at a cold strip mill factory is given to study the deformation, stress distribution and load capacity of the main girder with 3d - fea shell - to - solid submodel method
以某冷軋帶鋼廠橋式起重機偏軌箱形梁為例，採用三維有限元法「板到體子模型」技術，比較分析了加強板2種焊接方式下主梁的變形、應力分佈和承載能力。
分享友人