h-shaped h 中文意思是什麼
h-shaped h
解釋
形的-
Development of anti - skip device for roof bar of 11 mine h - bar trapezium - shaped support
礦用工字鋼梯形棚頂梁防滑裝置的研製 -
They can be found in circular cast houses of blast furnace, in oil - sealed dry gasholders and in workshops with curved cranes. cross sections of these curved members are of various types, such as il - shaped, i - shaped, channel, box and h section without any symmetrical axis
曲線梁在工業和民用建築中也常有應用，在高爐環形出鐵場、乾式煤氣櫃內部結構以及某些有工藝要求的廠房內，常需採用不同截面形式的環形曲梁。 -
According to the elastic bucking theory this paper reviews and compares the calculations that such member bend around the reat axis and the hollow axis as well as bend with torsion around the hollow axis. here this paper presents a formula of calculating b used in with the h - shaped anglicizing element. meanwhile, this paper deduces out a formula of calculating b. by, which the member could be controlled to only buckle around the real axis
本文根據彈性屈曲理論對雙肢格構式單軸對稱綴板柱繞實軸、虛軸以及彎扭屈曲進行了計算分析和比較，提出了繞虛軸側向屈曲的換算長細比_ （ oy ） = （ y ~ 2 + l ~ 2 ） ~ （ 1 / 2 ）中的值用h計算單元指出的計算公式，同時推導出了單軸對稱綴板柱只出現繞實軸彎曲屈曲的最小肢間間距b 。 -
Moreover, with the datum come from calculation and test, it seams that after the number of batten floor n > 3 the change of b effected by n is too weak to be ignored. hence, that indicates it is available that the laterlly buckle of the batten column with the single axis of symmetry could be calculated with b worked out from h - shaped anglicizing element without n
此外，由電算和實驗分析可見，值在綴板層數n 3以後，其變化受n值的影響不大，這說明用h計算單元導出的與綴板層數無關的值計算公式是可以用於單軸對稱綴板柱的側向屈的計算。 -
First super - low specific - speed centrifugal pump has a long and narrow flow passage for its high head and low capacity, and the power absorbed by disc friction is too high, so the efficiency is very low ; secondly the diffusion of flow passage is so high, that the reserved flow often emerges at the inlet and outlet of impeller. therefore the h ~ q characteristic curve is often hump - shaped, and at the low - capacity operating condition the instability often occurs ; thirdly the centrifugal pump at high - capacity operating condition is easy to overload because the n ~ q curve appears a rising trend
首先由於它的揚程較高、流量較小，所以它的流道狹長，圓盤摩擦損失較大，效率相對較低；其次由於它的流道擴散較嚴重，易在葉片進口產生迴流和在出口產生脫流，揚程流量特性曲線易出現駝峰，在小流量工況下易產生不穩定現象；第三，由於其功率流量曲線呈現上升趨勢，在大流量區運行時電機易過載。 -
Four groups of eight types of connection methods are suggested to be able to use for the joint of cold - formed rectangular tube - steel column and h - shaped beam by investigating the current research on the beam - to - column connection methods used at home and abroad, at the same time, a new type of connection is proposed in this article
本文在對國內外冷彎矩形鋼管與焊接箱形鋼管節點型式研究的基礎上總結出四類八種適合於冷彎矩形鋼管柱與h型鋼梁連接的節點型式，並提出一種新型節點連接型式，分別給出了相關的設計規定和使用條件。 -
Using the software of ansys, this thesis compares and analyzes the seismic behavior of the joint of cold - formed rectangular tube - steel column and h - shaped beam and the joint of welding box column and h - shaped beam, in order to research the influence for the cold forming process of the cold - formed rectangular tube - steel column
利用大型通用有限元分析軟體，對冷彎矩形鋼管柱與h型鋼梁連接節點與焊接箱形鋼管柱與h型鋼梁連接節點的抗震性能進行對比分析，探討出冷彎矩形鋼管的特性對節點抗震性能的影響。 -
Behavior analysis of short columns with encased h - shaped steel reinforced concrete under axial compression
型鋼混凝土軸壓短柱的受力性能分析 -
This series of abators belong to roller track shot blasting machines. they are mainly used to release stresses and clean rusts for large sized l shaped and h shaped steel structures in building and bridge construction industries
該系列通過式板、型材拋丸清理預處理線，是由預熱、拋丸處理、噴漆、烘乾等工序組成，該機廣泛應用於造船、汽車、橋梁、機械、集裝箱等行業的板材、型材及結構件的表面除繡、烘乾等流水作業。 -
Finally according to the load - capacity superposition concept, a simplified design equation for determination of the load capacity of circular composite columns with h - shaped and box - shaped structural steel is proposed. through comparison with the accurate computer - based method, it is found that the proposed simplified equation is accurate enough and can meet the requirement of practical applications
同時基於承載力疊加的概念，提出了配置工字型和箱型結構鋼的圓形截面組合柱在單向和雙向偏壓荷載下的承載力簡化計算公式，通過與精確的計算機數值迭代方法的比較發現，當荷載偏心較小時該簡化計算公式具有足夠的準確度，能夠滿足工程應用的要求。
分享友人