heat affecting 中文意思是什麼
heat affecting
解釋
熱影響-
At the same time, i discover that the number of the return air inlet has a little influecing and it can be neglected. when there is hot resource at upperside of the room, the hot jet and supply air jet together affecting. at the same lower part heat intensity, a utmost wind speed exist, the supply air speed lower, the more heat intensity on the upside, the less convecting transfer heat, whereas
對于上部有熱源的條件下，則其對流熱轉移量的變化關系是由熱射流與送風冷射流共同作用影響的，在下部熱源強度相同的條件下，存在一極限風速，在該風速以下，上部熱源強度越大，則對流熱轉移量越小，反之在該風速以上，上部熱源強度越大，則對流熱移量越大。 -
In this paper, the sensibility analysis of the factors affecting the temperature in well bore is relatively systematically made by using a large number of the data calculated with the borehole flow and heat transfer 3 ? d numerical model proposed by the author. the study shows that the thermophysical parameters of the drilling fluid and formation, etc. and the entrance temperature and circulating capacity, etc. of drilling fluid have a greater influence on the temperature in well bore. therefore, accurately mastering the thermophysical parameter values of penetrated formation and drilling fluid in well bore, considering the influence of the temperature and pressure on thermophysical parameters and accurately measuring such parameters as entrance temperature and discharge capacity of drilling fluid, etc. are of utmost importance for accurately simulating the temperature in well bore
利用由作者提出的井內流動和傳熱的三維數值模型計算所得的大量數據，文章對影響井內溫度的諸多因素進行了較系統的敏感性分析，研究表明：鉆井液和地層等的熱物理參數以及鉆井液的入口溫度、循環排量等對井內溫度有較大影響，因此，準確掌握所鉆地區地層和井內鉆井液的熱物理參數值，考慮溫度壓力對熱物理參數的影響，準確測量鉆井液的入口溫度、排量等參數值，對于井內溫度的準確模擬至關重要。 -
About heat loss, emphasis was mainly put on the part of exit gas, furthermore, a comprehensive summation in reference to possibilities affecting emission gas temperature increment were made and corresponding measures were given
在鍋爐的各項漏損中，著重分析影響排煙熱損失的諸因素。對影響鍋爐經濟運行的不利因素給出較為有效的預防措施，達到提高鍋爐運行經濟性的目的。 -
With fast development of our country " s gas industry and air ' s increasingly serious contamination in city, using gas instead of coal and supplying energy in high efficiency and cleanliness has become necessary way in city. there are different problems in the current heating ( air conditioning ) systems. in the cogeneration system, heat and power affect each other, heating - pump heating ( aie conditioning ) system can not satisfy the peak load very well, the cost of gas fuel in boilor heating sestem is so high. the high generating efficiency of the diesel - engine two - sourse heating ( air conditioning ) systems is limited in range of 100kw - 1000kw, the heating scope is so limited. combined cycle of two sourse heating ( air conditioning ) system is most suitable selection to buesness community with big scope my paper aim at this syetem ' s primary question when it is applied in our country - - - - bringing project into execution and technology economy feasibility and off - design performence, combined with a certain demonstrating project in beijing buesness community, going along with calculating and analyzing, drawing out some efficient datas and conclusions, based on this, bringing out primary alements affecting combined cycle of two sourse heating ( air conditioning ) system " economics
熱電聯產系統熱電相互牽連，熱泵供暖（空調）系統不容易很好地滿足尖峰負荷，鍋爐供暖系統供熱中天然氣燃料構成的成本過高，內燃機雙源供暖（空調）系統的高發電效率僅限於100kw - 1000kw負荷范圍，供熱面積有限。對于大面積的商業園區、居民小區，燃燒天然氣的燃氣-蒸汽聯合循環雙源供暖（空調）系統是最佳選擇之一。本論文針對該系統在我國應用時的主要問題- - -方案的技術實施與技術經濟可行性，結合北京某一商業園區示範工程，進行了系統的計算與分析，得到了有效的數據與結論，在此基礎上，提出影響聯合循環雙源供暖（空調）系統經濟性的主要因素，並進行敏感性分析，得出有益的結論；最後通過各種供暖方案的比較分析回答了某些人對該系統的疑慮和不解，並指出系統的優化方向。 -
Condoms will age as time goes by, resulting in impairment of the tenacity. exposure to intense heat and light will also accelerate ageing of the rubber, thus weakening the pulling force and affecting its overall function. do not buy condoms displayed under decorative light and sunlight in the shop
安全套在出廠之後，會隨著時間而出現老化現象，影響其韌力，高熱或強光也會令橡膠加速老化，拉力強度變弱，以致影響其功能，在選購時，如產品存放于射燈或陽光照射的地方，便不應購買，安全套應放置在陰涼的地方。 -
Factors of affecting exergetic efficiency of heat exchanger and their functions in thermoeconomic analysis
效率的影響因素及其在熱經濟分析中的作用 -
The mathematical and physical dynamic models are given based on the adsorbent theory of porous medium. its running and parameters affecting its performance are numerically studied and the method that control the water content in the absorbent bed is recommended. the improvement on system configuration to recover heat is discussed and the operation scheme is given
利用多孔介質吸附模型和平衡吸附壓力的概念建立了該系統工作過程的物理數學模型，數值模擬的方法模擬了其工作過程和影響因素，提出了控制吸附床含濕量的方案，驗證了改進流程回收能量的可行性並給出了操作方案，提出並分析了用熱電製冷器回收水蒸氣潛熱節約電能的方法。 -
For adapting to the need of industrialization and improving the properties of materials, the method of mechanical activation has introduced on the basis of traditional calcinations at high temperature. the stardard spinel limn204 is prepared by the mechanical activation - high temperature solid synthesis method. the thermodynamic property, the physical - chemistry performance and the producing techniques of. battery have been studied by means of thermogravimetry ( tg ), differential scanning calorimetry ( dsc ), x - ray diffraction ( xrd ), scanning electric microscopy ( sem ) as well as various electrochemical analysis methods. studies show that synthesis temperature, calcinations time, recipe of raw materials, heat treatment and particle size of products are main factors affecting the performances of limn204 cathode materials. with the increment of synthesis temperature and time, the structure and crystal of products are getting to perfect
隨著合成溫度和時間的增加，產物的結構和晶型越趨于完善，但在1100得到的產物有燒結和晶粒增大的現象，恆溫時間超過24h后對材料的性能影響不是很大； li mn比在0 . 95 1 . 05 2的條件下都可得到標準的尖晶石limn _ 2o _ 4 ，尤其當li mn比為1 . 05 2時，所合成的材料具有較好的電化學性能；通過兩段合成法制備的產物性能要比一段合成法法制備的產物性能好，而兩段間隔合成法比兩段連續合成法處理的材料性能更佳；顆粒的粒度隨著球磨時間的延長而減小，比表面昆明理工大學碩士學位論文摘要卻增大，粒度小且分佈范圍窄的材料有利於鏗離子的擴散。 -
There is no thoroughly rounded theory about displacement ventilation system in our country at present and our research begins recently. the study work of this paper will be useful for further optimization design of displacement ventilation system. this dissertation includes five parts. the first part introduces the development of the displacement ventilation and the background of research in domestic and oversea. in the second part, it gives working principle of displacement ventilation system and it ’ s advantages to the mixture ventilation. the study also gives a series of indexes to evaluate displacement ventilation system and specifies air supply terminal device and so on. it is needed to simulate and analyse the velocity field, temperature field and distribution of flow field. this is the third part. the forth part specifies the simulative method for thermal stratification of displacement ventilation system. it gives some factors affecting thermal stratification height such as inlet temperature, inlet velocity, heat transfer of wall body, distance of heat source and so on
本文的研究工作主要包括以下幾個方面的內容: （ 1 ）綜述了國內外相關的研究現狀和研究背景; （ 2 ）簡介了置換通風的工作原理，並分析了它相對于混合通風的優良特性及評價指標、末端裝置等; （ 3 ）對採用置換通風方式房間的溫度場、速度場和氣流分佈進行了模擬計算與分析; （ 4 ）對採用置換通風方式房間的熱力分層高度進行了模擬計算，並分析其影響因素，如:送風溫度、送風速度、圍護結構傳熱和熱源分佈等; （ 5 ）擬合了無量綱熱力分層高度相應于送風溫度t 、送風速度v 、熱源間距離l和圍護結構傳熱q的經驗公式。 -
As experiments reveals, the moisture diffusion, heat conduction and mechanical response in polymers are mutually affecting behaviors
有試驗發現，高聚物中濕分、溫度和應力是相互影響的。 -
The research on the air conditioning matching of haishi sy - 6480 microbus. to the question of hard circumstance and excessive affecting factors when automobile air conditioning ( aac ) is working. based on the characteristic of scroll compressor and studying of the affecting of designed parameter, summing - up experiential arithmetic of aac heat exchanger and deciding the refrigerant charge by experiment
針對汽車空調運行條件惡劣，運行時受影響因素多的特點，對汽車空調中設計參數的選擇對設計結果的影響進行研究，並充分考慮所選壓縮機特點進行合理選擇，總結出可以在一定范圍內使用的經驗演算法，並利用試驗的方法確定汽車空調系統的製冷劑充注量。 -
The theoretical analysis of large cryocondensation pump for nbi was mainly concerned. this paper emphasized on analyzing and calculating the heat load of cryocondensation pump, simulating thermal transmission coefficient and molecule transmission coefficient of radiation baffle according to monte carlo method, analyzing the process on cryo - surface and the factor of affecting pumping speed and hydrogen layer thickness of influencing cryo - parameter, etc. finally by verifying the pumping speed on large cryocondensation pump for neutral beam injection system, the pumping speed of 4. 0x105l / s ( for h2 ) was proven to be reasonable
本文首先介紹了中性束注入系統的國內外發展狀況，闡述了中科院等離子體所ht - 7中性束注入系統的構成，主要對用於中性束注入系統的大型低溫冷凝泵的特性進行了理論分析；對冷凝抽氣面的熱負載進行了分析計算；用蒙特卡羅法對輻射擋板的分子傳輸幾率與熱傳輸幾率進行了模擬計算；研究了低溫表面的處理方法對抽速的影響以及氫層厚度對各低溫參數的影響；最後對用於中性束注入系統的大型低溫冷凝泵的抽速進行了驗證，得出的結論是：選取40萬升秒的抽速是合理的。 -
How to select the optimized model scheme for the air - conditioner heat and cool sources based on the local conditions has become the focus of the engineers and users, which is also an important factor affecting the general society energy consumption and project investment
如何根據實際條件正確選擇冷熱源已成為設計工作者和用戶經常碰到的一個問題，也是影響社會總能耗和工程投資的重要因數。 -
Based on the analytical result of stirring kinetics, the maximal affecting factors to the size and distribution homogeneous degree of intermetallic al3fe reinforcement phase in al matrix during the stage of heat preservation stirring are studied, and some important parameters of stirring equipment and stirring process are ascertained, and the stirring processing is optimized
根據攪拌動力學分析的結果，研究了攪拌過程中對金屬間化合物al _ 3fe強化相尺寸大小和分佈均勻度的影響的因素，確定了攪拌設備和攪拌過程的幾個重要參數，並對攪拌工藝進行了優化設計。 -
In technical aspect, changing the sealed furnace into heat - air circulation structure, it makes the temperature of the drying works be average, the humidity is got rid of in time which affecting the quality of the product
在工藝上，將原封閉的乾燥爐結構改為熱風循環乾燥爐結構，這樣有利於改善原乾燥物品在爐內溫度不均勻、潮氣不能及時排除等情況而影響產修品質量。 -
In chapter 2, a new ir imaging model for city buildings has been established based on meteorology, heat transfer and infrared physics. we first analysis all kinds of main factors affecting the ir characteristic of city buildings, then by using the methods such as multi - layer finite difference the surface temperatures of building and other surrounding objects are acquired. combining the methods of classified modeling and special modeling we constitute the large - scale complex urban ir scene and render the ir images of urban scene at various time
本文第二章從氣象學、傳熱學和紅外物理學原理出發，分析了影響城市建築物紅外特性的各種主要因素，採用多層有限差分等方法求解建築物及周圍物體的表面溫度，建立了城市建築物紅外成像模型；採用分類建模和特殊建模相結合的方法構建了大規模復雜城市場景的紅外模型，繪制出了不同時刻城市復雜場景紅外成像圖。
分享友人