heat treatment oil 中文意思是什麼
heat treatment oil
解釋
熱處理用油-
As burning oil burning coal burning large scale car bottom heat treatment furnace
燃氣燃油燃煤大型臺車爐 -
Heat treatment equipment high vacuum gas oil quenching oven
熱處理設備：高真空氣油淬兩用爐 -
Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously
應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。 -
Product description : this series product has entire auto - lubrication systems and the ordinary two big kinds supplies to select, this machine major parts cancels the needle, cam and the ball bearing all uses the high quality import components, also selects the high quality steel products quenching heat treatment to the main stress components, the essential components uses special phosphorus processing, the foreign dew components all adopts special - purpose seal - up device and drains the oil the measure, therefore, entire causes machine throughout to locate the lubrication is reliable, the revolution is steady, under the high speed low chirp condition works
本系列產品具有全自動潤滑型及普通型兩大類以供選用，本機主要零件勾針，凸輪及滾珠均採用優質進口零件，對主要受力零件亦選用優質鋼材淬火熱處理，關鍵零件則採用專門磷化處理，對外露零件均採取專用密封裝置及排油措施，因此，使整機始終處于潤滑可靠，運轉平穩，高速低噪的條件下工作。 -
The changing carbon potential carburization - hot oil matrempering technology of helical bevel gear for automobile driven axle is introduced in this article. the board test and production application show that the technology not only quenchs directly gear after carbrization, but also decreases the heat treatment deformation and raises the contact fatigue life of gear
介紹了汽車驅動橋螺旋錐齒輪的變碳勢滲碳一熱油分級淬火工藝，臺架試驗及生產應用表明，該工藝與專用滲碳淬火掛具相結合，不僅可實現齒輪滲碳后直接淬火，而且熱處理變形小，齒輪接觸疲勞壽命也有所提高。 -
Founded in september 1997, the company occupies an area of 35000 square meters and has 50 staffs, including 3 engineers, 2 vice senior engineers and 4 engineers. with the help of some domestic specialists who engaged in the research on induction heated quenching - tempering treatment in weapon and space industries. we developed the first induction heat oil tempered elastic wire production line in china by ourselves. this production line was put use in august 1998, and was enlisted in the spak programme in 2000 serial number : 369, programme code : 00b101d691004
創建於1997年9月，佔地35000平方米，員工50名，其中研究員級高工3名，高工2名，工程師4名。依靠國內一批在軍工企業長期從事感應加熱調質處理研究的專家，自行研製成功國內第一條彈性線材感應加熱油淬火-回火生產線，並於1998年投產。 -
Its s applicable for metallurgy, machinery, oil field, chemical engineering, mine, electricity, traffic and manufacturing to filter hydraulic oil, hydraulic transmission oil, gear oil, gasoline engine oil, diesel engine oil, compressor oil, freezer oil, heat treatment oil, ect
廣泛適用於冶金機械油田化工礦山電力交通製造等行業對液壓油液力傳動油輪油汽油機油柴油機油壓縮機油冷凍機油熱處理油等的凈化處理。
分享友人