high-heat flow 中文意思是什麼

high-heat flow 解釋
高熱流
  • high : adj 1 高的〈指物，形容人的身高用 tall〉；高處的；高地的。2 高級的，高等的，高位的，重要的。3 高尚...
  • heat : n 1 熱；熱力；熱度；熱量。2 體溫；發燒。3 （氣候的）高溫，暑氣。4 【冶金】熔煉的爐次；裝爐量；一...
  • flow : vi 1 流，流動。2 （血液等）流通，循環。3 流過；川流不息；（時間）飛逝；（言語等）流暢。4 （衣服、...
  1. The results indicate that : the high positioned air inflow do good to heat transfer in rotator disk ; different size of radial outflow have small effects on flow and heat transfer ; the heat transfer near rotating disk increases as rotating reynold number increases or non - dimensional mass flow rate increases

    結果表明，高位軸向進氣對轉盤換熱有利；不同的徑向出口大小對盤腔內的流動換熱影響不大；隨旋轉雷諾數和無量綱質量流量增加，轉盤盤面的換熱效果增強。
  2. Theoretical study for evaporative heat transfer of annular two - phase flow of liquid film and high - velocity air in vertically heated tubes

    高速空氣環狀兩相流的蒸發換熱特性理論分析
  3. In this paper, high heat penetration into a moving particulate bed is described mathematically with a comprehensive heat and mass transfer model. the distribution of gas velocity and pressure, the temperature field of gas and solid in the moving particulate bed are examined for different conditions. the results show that thermal penetration into the moving packed - bed particles by fluid flow in porous media is high only in the position near the gas entrance. the thermal penetration thickness tends to increase with the fluid flow velocity and decrease with the particle moving velocity. in the region of thermal penetration, the porosity of solid bed has significant effect on gas field and pressure loss. it is feasible to reduce the gas pressure loss by a larger width / height packed bed in design and operation. the correspondence between thermal infection depth and particle bed height would be helpful to keep high oapacity of reactor and reduce the cost of operation

    針對移動顆粒床中物料層內的高溫氣體滲流傳熱現象，考慮滲流與傳熱的相互作用，採用局部非熱平衡假設建立了多孔介質滲流傳熱物理數學模型並進行了數值計算.研究了不同情況下床內填充多孔介質中的流速、氣固溫度和床層壓力損失.計算結果表明，高溫熱氣對移動床顆粒料層的熱滲透主要發生在滲流入口端區域，增大入口滲流速度以及減小床層物料下移速度將導致物料溫度沿床高慢速下降，熱滲透深度擴大，熱滲透作用區域內的物料溫度水平提高.在熱滲透作用區域，孔隙率對流場和壓力損失有很大的影響.研究結果對于移動顆粒床反應器的設計與運行具有一定的參考作用
  4. The analysis of the large - scale synoptic situation shows that strong precipitation is closely related to the explosion of monsoon and the intensification of cross - equatorial flow which bring a lot of vapor and meet with cold masses at the eastern of northwest district on 8th, june causing extremely heavy rainfall ; that subtropical high - level jet at 200hpa, subtropical high at 500hpa and low - level jet at 850hpa are the weather backgrounds favorable to strong precipitation ; that the pattern of eastern highs and western lows and the establishment of a low - level jet and the coupling between upper - and low - level patterns that determine that the rain occurred in the east of the northwest china ( on average, this is the rainy season for the south of china, but not for the northwest china ) ; that water vapor comes from southerly and easterly flow which converge at the eastern of northwest district with convergence mainly in lower levels and pbl ; that the high value of the whole - level apparent heat source < q1 > is near the area of large rainfall in the direction of northeasterly - southwesterly agreeable to shear line very well and the condensation latent heat releasing is main heat source with vertical advection item playing key role in q1 and q2 ; that there is a vertical secondary circulation crossing low - lever jet whose ascending branch is at the area of large rainfall ; that the construction of convection instability and conditional symmetry instability results that there is not only deep thermal instability, but also moisture influx and triggering mechanism of thermal instability causing strong torrential rain

    作為對比，本文還對2002年6月24 - 25日發生在北京地區的強地形雨進行了分析，並討論陜南、北京地區兩地暴雨的異同點以及地形作用的共性和個性，為兩地暴雨預報提供有益的參考，得出了一些很有意義的結果： 1大尺度環流背景分析表明： （ 1 ） 「 02 . 6 」強降水與6月上旬越赤道氣流和季風爆發密切相關，攜帶大量水汽的偏南氣流與冷空氣於6月8日交匯在西北地區東部，導致了這次強降水的發生； （ 2 ） 200hpa的副熱帶西風急流、 500hpa副高以及850hpa的低空急流的配置非常有利於本文分析之陜西強降水的發展與維持。大尺度形勢分析表明，東高西低形勢場、低空急流的建立和高低空形勢的配置決定了這場降雨出現在西北地區東部。與暴雨區相聯系，存在一支橫越低空急流的經向垂直環流，暴雨區處于該垂直環流的上升支； （ 3 ）偏南和偏東氣流水汽通道在西北地區東部交匯，水汽的輻合積聚主要在對流層低層和行星邊界層內完成； （ 4 ）整層的視熱源< q _ 1 >高值區在暴雨區附近呈東北-西南向分佈，與切變線走向非常一致，降水產生的凝結潛熱釋放是強降水區大氣的主要熱源。
  5. Excellent in solderability and high heat resistance with either flow or reflow soklering

    可焊性和耐焊性優，適用於流焊和再流焊。
  6. Of the currently available coolers for electronic products with a high heat flux, microchannel heat sinks have been proved to be able to provide the best heat transfer performance and are one of the most promising coolers. the manifold microchannel ( mmc ) heat sink has many advantages such as low thermal resistance, compact structure, little amount of coolant, low flow rate, uniform temperature distribution along the flow direction and many others, so it is able to provide the best heat transfer performance : lowering the maxmal temperature and the temperature difference

    在目前高熱通量電子產品冷卻器中，微通道熱沉已被證實是傳熱性能最佳且最具應用潛力的冷卻方式之一，而歧管式微通道熱沉因具有低熱阻、結構緊湊、所需冷卻液量小、沿流動方向溫度分佈均勻等優點則成為減小電子元器件換熱表面最高溫度、降低溫度變化的一種有效方法。
  7. Under the condition mention in this physical model, when there is a high rotor heat load, the effect of the axial direction gas - flow to the total heat - emitting capability is not very great

    轉子高熱負荷條件下，該模型建模條件下由氣隙楔度所產生的軸向風量對總散熱能力的貢獻較小。
  8. Kunming belongs to the low latitude plateau mountainous country monsoon climate, because of locating in the western region of yungui plateau, the degree of latitude is low, the elevation is high, there are the wumeng mountains to be as the natural screen in the north, separating the cold air to go down south, the whole area is subjected to influence that come from southwest and warm moisture of indian ocean s flow more, adding there are the plateau lakes to regulate degree of humidity, becoming the four seasons of " summer have no intense heat, winter have no strict and cold ", such as pleasant weather of the spring

    昆明屬低緯高原山地季風氣候，由於地處雲貴高原西部，緯度低，海拔高，北部有烏蒙山等群山作為天然屏障，阻隔南下的冷空氣，全區多受來自印度洋西南暖濕氣流的影響，加之有高原湖泊滇池陽宗海調節溫濕度，形成「夏無酷暑，冬無嚴寒」四季如春的宜人氣候。年平均氣溫為14 . 5 ，最熱月平均氣溫19 . 7 ，最冷月平均氣溫7 . 5 ，年平均日照時數為2400多小時。
  9. Abstract : the causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    文摘:分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上
  10. The causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上
  11. 3, carry out detailed numerical simulation and analysis for heat extraction of deep - seated hdr based on the tengcong prefecture, reach the major variety rule of rock mass stress, temperature, fracture width depending on the heat extraction. ( 1 ) in the hot dry rock geotherraal energy extraction system, transportation of energy and flow of water arise mainly through the fracture, the lower temperature water attain the high temperature from the injection well to production well through conduction convection and take away the thermal from wall rock

    3 、認真地對騰沖高溫巖體地熱開發進行了數值模擬計算和分析，得出了地熱開發過程中巖體應力、溫度以及裂縫寬度隨地熱提取的變化規律等重要結論： （ 1 ）在高溫巖體地熱開發系統中，能量的運移、輸送與水的流動主要通過裂縫面發生，注入的低溫水在流到生產井的過程中，發生傳導、對流、吸收圍巖熱量，達到升溫的目的。
  12. A solid - liquid fluidized bed has been designed and installed, which will be used in the heat exchanging and descale field. the experimental study for distributor design was carried out and the particles distribution in the tubes of the solid - liquid fluidized bed under different operating conditions was studied by using the ccd measure system. experimental results show that heterogeneous pores distributor which was arranged in the inlet chamber of the solid - liquid fluidized bed can improve the nonuniform distribution of particles in the pipe bundle under high flow rate. the nonuniform decreases by decreasing the mount of pore, but the solid holdup decreases too. the particles distribution is influenced by the position of the heterogeneous pores distributor

    實驗結果表明：在液固循環流化床進口段安裝可調節高度的變孔徑分佈板，能在較高的流速下，較好的改善固體顆粒在管束中的不均勻分佈；開孔率越小固體顆粒在管束中的分佈越均勻，但管束中粒子的平均固含率也越小；分佈板的安裝高度對顆粒的分佈有很大的影響，在實驗范圍內分佈板的安裝距離管束入口處越遠，顆粒在管束中的分佈越均勻。
  13. Combining burning and heat exchange as a whole, this furnace adopts the novel indirect heating technology of performing heat exchange at high temperature position of the furnace, inside which, smoke and air flow separately, heating has no contamination, thermal efficient reaches 60 - 75 %, therefore, it features speedy temperature rise, compact dimension, convenient installation, reliable operation and lower cost ( only half of that by boiler heating system )

    該爐集燃燒與換熱為一體以爐體高溫部分進行換熱的最新間接加熱技術，煙和空氣各行其道，加熱絕對無污染，熱效率高達60 - 75 % ，升溫快，體積小，安裝方便，使用可靠且價格低，與一噸鍋爐相比，該加熱系統只相當于鍋爐加熱系統價格的一半。
  14. By using the computerized dynamic modeling, the authors show that some quickly subsiding stages were involved in the process of basin formation, and the heat flow value generally varied from low to high as a whole, despite the fact that it may show alternatively increasing and decreasing trends at different stages, which demonstrates that the tectonic movement affected the heat flow value significantly

    通過計算機技術的動態模擬，表明該區盆地演化過程中存在多個快速沈降期；其古熱流總體上由低到高變化，但在不同的演化階段表現不同，有升高也有降低，同時也反映了構造運動對熱流變化的影響。
  15. The immersion electrical heater is chiefly applied in the direct contact mode of fluid heating. it features fast heat exchange and high thermal efficiency. it has the varieties of water heater, oil heater and gas heater. its heating element power density, i. e. the power per unit of heating area of the heating element, is an important parameter of the electrical heating element, which has a direct bearing on the performance and working life. the working out of the value is a highly specialized problem, being under the influence of many factors ( media flow rate, tempt, physical and chemical properties and direction in which the medium flows past the element etc )

    浸入式電加熱器主要用於直接對流體接觸加熱的場合，具有熱交換快，熱效率高等特點，分為水用加熱器、油用加熱器、氣體用加熱器，加熱元件的功率密度：即電加熱元件單位發熱面積上的功率，它是電加熱元件極重要的參數，直接影響加熱器的使用性能及使用壽命，它的取值是一個非常專業的問題，受到許多因素的影響（如介質的流速、溫度、物理和化學性質及介質流過加熱元件的方向等等） 。
  16. The fem results indicated that as to the rough surfaces in sliding contact, the value of the contact pressure was very high which coursed a high value of the heat flow rate, meanwhile the sliding time was not enough for the frictional heat to transfer, thus the highest value of the body temperature occurred just on the sliding surfaces, which possessed a sharp thermal gradient in direction perpendicular to the sliding surface. so the great thermal stress was caused just by the sharp gradient and the thermal elastic distortion with which the contact pressure changed occurred simultaneously, thus this change of the contact pressure would affect the temperature distribution in return

    對于相對滑動的粗糙表面，因實際接觸面積小而導致接觸壓力很大，這樣使得熱流密度會很大，同時由於滑動時間很短，熱來不及傳導，最高溫度發生在摩擦表面，在垂直於摩擦面的方向有很大的溫度梯度，使得熱應力很大，且最大應力發生在表面，同時產生熱彈性變形，這種變形使得接觸區域內的壓力分佈發生變化，這種變化又反過來影響了接觸區域的溫度分佈。
  17. ( 3 ) on the background of the development of an ignition rocket, some application investigations have been carried out. some parameters related to water - resistant ignition mixture, the charge of ignition rocket, such as heat - flow, density of charges, structure of charges, coating and its process, area ratio of nozzle and high temperature corrosion of the nozzle, were calculated and studied, respectively. on the basis of the above studies, an ignition rocket was successfully developed

    （ 3 ）進行了應用研究，以某系列點火發動機的研製為背景，分別對耐水點火藥用作點火發動機裝藥所涉及的能量衡算、裝藥密度、裝藥結構、包覆及其工藝、喉面比及噴口燒蝕等問題進行了分析和實驗研究，在這些研究的基礎上成功地製作了一種點火發動機。
  18. With the developments of very large scale integration ( vlsi ) and high - speed large computers, the specific rate of heat flow increases rapidly

    隨著隨著超大規模集成電路（ vlsi ）和高速大型電子計算機的發展，集成電路和計算機內的熱流密度很快地增加。
  19. Powerful refrigeration ： turbo air flow is adopted with high heat exchange rate and excellent refrigerating effects

    製冷強：採用渦流式風流，熱交換效果絕佳，製冷效果好。
  20. Thermal performance of building materials and products - determination of thermal resistande by means of guarded hot plate and heat flow meter methods - thick products of high and medium thermal resistance

    建築材料和產品的熱性能.用防護熱板和熱流量計法測定熱阻.厚產品的高熱阻和中熱阻
分享友人
分享到 Line

分享到臉書