hot pressing 中文意思是什麼
hot pressing
解釋
加壓燒結法-
There are many defects in the tic preforms prepared by cold pressing, such as small air holes and cracks. the tic preforms prepared by hot pressing have better qualities
冷壓成型預制體一般存在分層、裂紋等缺陷，未造粒的粉體壓制時流動性、均勻性差是根本原因。 -
In chapter two, we fabricated r - ni - fe / al2o3 nanocomposites successfully by using ball - milling mixing method plus hot - pressing process. meanwhile, their microstructures are characterized by x - ray diffraction ( xrd ) analyser, transmission electron microscopy ( tem ), field emission scanning electron microscopy ( fe - sem ) and brunauer - emmett - teller ( bet ). the results indicate that ni - fe particles are homogenously dispersed in the matrix in the composites
在第二章中，我們採用高能球磨混合方法加上熱壓燒結工藝，成功制備了ni - 20fe al _ 2o _ 3納米復合材料，並通過x射線衍射儀（ xrd ） 、透射電鏡（ tem ） 、場發射掃描電鏡（ fe - sem ） 、比表面孔隙儀（ bet ）對該復合材料的微結構進行了表徵。 -
Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )
本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。 -
The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads
本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。 -
Cooperation project diamond circular saw blades with cool and hot pressing
冷熱壓金剛石圓鋸片合作項目 -
In the paper we mainly researched space gainp2 / gaas / ge high efficiency tandem cells " making process by home - made low pressure mocvd technology and new solar concentrators. firstly, we presented reseached and development of solar cells in china and foreign countries ; secondly, on the basis of fundamental priciples and theories, we discussed some factors of influcing conversion efficiency of solar cells, and analysed the i - v output feature of two - junction tandem cells ; then the design concept of gainp2 / gaas / ge two - junction tandem cells was discussed, the detailed aspects of gainp2 / gaas / ge tandem cells epitaxy growth by low pressure mocvd was studied, and some questions on epitaxy growth ( such as crystal qualities, interface stress, element interdiffusion, n - and p - type doping et all ) were solved ; after that, the cell fabrication process was described ; finally, we reseached the hot pressing and mould process technology of an arched line - focus fresnel lens made by pmma, designed and fixed new solar concentrators
本文致力於用自製的低壓mocvd裝置進行cainp _ 2 / gaas / ge空間用高效級聯太陽能電池製作的工藝以及聚光太陽能電池組件的研究。首先，介紹了國內外太陽能電池的研究現狀及應用情況；其次，運用太陽能電池基本原理討論影響電池轉換效率的因素，分析了級聯電池的伏安特性；隨后，討論了cainp _ 2 / gaas / ge雙結級聯電池的結構設計理念，研究了採用低壓mocvd技術生長cainp _ 2 / gaas / ge級聯太陽電池材料的工藝過程，解決了異質材料生長的結晶質量、界面應力、材料互擴散以及材料n 、 p型摻雜等一系列問題；然後總結了級聯電池的后工藝製作；最後，研究了以pmma為材料的菲涅耳線聚焦透鏡的熱壓成型工藝及其模具的加工工藝，設計並安裝完成新型聚光太陽能電池組件。 -
By hot pressing, the licoo _ 2 target was produced. different moulds were used in the hot pressing including the graphite mould and the sic mould
在熱壓法制備licoo _ 2靶材的過程中，使用了石墨模具，碳化硅模具。 -
The experimental results demonstrate that the suitable mea hot - pressing temperature and pressure are 120 and 15. 5mpa, respectively. the optimum catalyst loading in anode is 4 mg pt / cm2, and the best contents of nafion ionomer in anode and cathode layer are 45wt % and 35. 3wt %, respectively
實驗結果顯示，制備膜電極時最佳的熱壓溫度和壓力分別為120和15 . 5mpa ；陽極催化劑的適宜載量為4mgpt / cm2 ；陽極和陰極催化劑層的nafion最優含量分別為45 . 0wt %和35 . 3wt % 。 -
Study on limn2o4 synthesized by hot - pressing method and on lithium getting off the products
4的熱壓合成及鋰脫嵌研究 -
Effect of hot - pressing temperature and natural curing time on properties of fast - curing cement particle board
熱壓溫度和養護時間對快速固化水泥刨花板性能的影響 -
Have been put into use and upgraded for many years, perfect quality and tehnology obtained day by day. introduced hot pressing high frequency adhesive equipment and high density sewing machines are used to make the body of airboat, the parts of the body is sewed together in high density before they are adhesived by hot high frequency, three strings used as safety belt are added to the body, the clothe for the body has been strictly examined to ensure no gas escaping
遙控航空廣告飛艇艇身採用先進的進口導軌輥壓高頻熱合機及高密腳工業縫紉機承製。艇體在艇瓣熱合之前先用結實的線將合線緊密縫合，然後用高頻熱合機熱合，並在艇體上加制了三道束身安全腰帶，艇體布料經過嚴格的光透檢漏法嚴查，確保不漏氣。 -
Testing method for colour fastness to hot pressing
耐熱壓熨色牢度的試驗方法 -
An experiment was conducted to study the effects of hot - pressing temperature on properties of wheat straw - plastic composites made from wheat straw and recycled polyethylene ( pe ) using isocyanate as adhesive through multi - factor orthogonal experiment and single - factor experiment
摘要通過正交試驗和單因子試驗，以麥秸和廢舊聚乙烯塑料為原料，使用異氰酸酯膠黏劑壓制麥秸塑料刨花板，分析熱壓溫度對麥秸聚乙烯復合材料性能的影響。 -
A uniaxial hot - pressing test and a physical modeling simulation are performed to investigate the orientational alignment of crystals, and a new attempt to strengthen mica glass - ceramics is made
摘要利用單軸熱壓變形物理模型進行實驗類比，對強化雲母微晶玻璃的新途徑晶體定向排列進行了研究。 -
The results show that the completion degree of orientational alignment in mica plates remarkably varies in different sites of sample body, which is attributed to uneven deformation under the uniaxial hot - pressing condition
結果表明：在單軸壓縮變形方式下，雲母微晶玻璃材料截面上的流變程度不均勻，導致晶體定向排列程度差異大。 -
In this article, by rf sputtering the licoo _ 2 film was produced. by hot pressing and cold pressing ( and sintering ), the licoo _ 2 targets used in the rf sputtering were produced differently. both technics of the preparation of the licoo _ 2 film and the licoo _ 2 target were studied
本文使用熱壓燒結方法和冷壓后燒結方法制備了磁控濺射用的licoo _ 2靶材，並使用磁控濺射方法制備了licoo _ 2薄膜，對兩者的制備工藝進行了研究。 -
1 the company has imported one set world advantaged test calibrator with matrix tensile stress and purchased international advanced level of continuous sinter kiln, oir press, opening blade machine, cut - off tester, cintrifugal tester and mould. they made in china. these equipment have about 41 sets. diamond circular saw blades with cool and hot pressing can be produced two million pieces per year
1引進國際先進的基體張力測試校準儀一臺，購入具有國際先進水平的國內製造的連續式燒結爐油壓機開刃機切割試驗機離心實驗機工夾量模具等41臺套。生產冷熱壓金剛石圓鋸片200萬片。 -
The fiber / resin / aluminum alloy laminated composites have been fabricated by using a method of hot pressing and solidifying. the interface bonding strength of aluminum alloy / resin interface, mechanical property and anti - vibration damping property are investigated
採用熱壓固化法制備了纖維樹脂鋁合金疊層復合材料，並研究其界面結合、力學性能及抗振阻尼性能。 -
Hot - pressing sintering of w - 15cu alloy
熱壓燒結制備高密度鎢銅合金 -
This control system realizes the functions such as produce the real - time control, the trends show, the accident reports, production report, etc. through the analysis of continuous hot - pressing technology of mdf, this paper introduces the fuzzy control method on the control of hot - pressing times in order to achieve and improve production quality and product efficiency
文中介紹了控制系統的組態過程，對網路設置進行了詳細說明。該控制系統實現了生產的實時監控、動態顯示、事故報警和生產報表等功能。本文通過對連續式熱壓機的熱壓生產工藝過程進行了分析，在連續式熱壓機熱壓時間的控制上引入了模糊控制方法。
分享友人