hot tensile 中文意思是什麼
hot tensile
解釋
高溫抗張強度-
Specification for hot rolled and hot rolled and processed high tensile alloy steel bars for the prestressing of concrete
混凝土預加應力用熱軋和熱軋並處理的高抗拉強度的合金鋼筋規范 -
To measure the tensile strength of hot rolled bars, steel wire and weld strength of steel
測試熱軋鋼筋、鋼絲和扁鋼抗拉力強度和焊接強度 -
The observation and analysis for the tensile fracture of hot rolled plate by sem and eds is a valid method to discover the influence of the inclusions in the plate on the elongation
摘要應用掃描電子顯微鏡及能譜儀對熱軋中板拉伸斷口進行形貌觀察和夾雜物類型分析，以探討熱軋中板中夾雜物對其伸長率的影響。 -
1 the company has imported one set world advantaged test calibrator with matrix tensile stress and purchased international advanced level of continuous sinter kiln, oir press, opening blade machine, cut - off tester, cintrifugal tester and mould. they made in china. these equipment have about 41 sets. diamond circular saw blades with cool and hot pressing can be produced two million pieces per year
1引進國際先進的基體張力測試校準儀一臺，購入具有國際先進水平的國內製造的連續式燒結爐油壓機開刃機切割試驗機離心實驗機工夾量模具等41臺套。生產冷熱壓金剛石圓鋸片200萬片。 -
In this paper, 130mm diameter hot - rolled bars ( 3 transus temperature is 798 c ) were used in experiments. the superplastic property of ti - 1023 alloy was studied systematically by the experiments of tensile and compression. the preparation method of fine - crystalline structure and the processing parameters of superplastic forging are optimized
本文以130mm熱軋棒材為原材料，通過超塑性拉伸和超塑性壓縮試驗，對ti - 1023合金的超塑性進行系統研究，研究坯料細晶組織制備方法，優化超塑成形工藝參數，為高筋薄腹板復雜形狀ti - 1023合金鍛件超塑性等溫模鍛工藝的制定提供試驗依據。 -
The relationship of true stress and true strain for the mid - strength weldable 1420 aluminum - lithium alloy has been investigated in this thesis by high temperature compression testing and high temperature tensile testing on different hot deformation conditions. the interdependence of flow stress, strain rate, strain and deformation temperature for the alloy at high temperature has been studied
本文通過高溫壓縮和高溫拉伸試驗，研究了中強可焊1420鋁鋰合金熱變形時不同變形條件下的應力-應變關系、變形條件對合金流變應力的影響；運用多元回歸分析方法，採用c語言編程確定了合金的本構關系方程；引入z參數，求解了部分材料常數，並用於材料的組織性能研究中。 -
Based on the hot tensile test results, there exists a cooling rate at which a minimum reduction in area occurs and the hot ductility of the sn - doped steel is worse than that of the sn - undoped steel. when the cooling rate is lower or higher than 10 / s, the hot ductility is increased
連續冷卻到750 800范圍內拉伸時，存在一個冷卻速率（ 10 s ） ，以這個冷卻速率進行冷卻，試樣的斷面收縮率最小，熱塑性最差；當冷卻速率大於或者小於這個冷卻速率時，試樣的斷面收縮率均會增大，熱塑性增強。 -
If there are high temperature gradient between cool liner and hot liner, compressive plastic strain appear at that transient time, which lead to gas film wall bearing high tensile stress at high temperature. high tensile stress is one of main reasons which destroy combustor
分析表明，起動過程中由於熱傳導滯后引發的溫度梯度可以導致火焰筒氣膜唇邊在起動瞬間發生較大的壓縮塑性應變，進而使得該區域在工作時承受較高水平的拉伸應力，高的拉應力會導致火焰筒萌生裂紋。
分享友人