hot-forging die 中文意思是什麼
hot-forging die
解釋
熱鍛模-
The research on the overheat of h13 hot die steel forging
13熱模鋼鍛材過熱的研究 -
Abstract : in the paper, the hot crack for the forging die made by methodsof squeeze casting is analyzed, how to reduce the hot crack is also given out
文摘:從生產實際出發，分析了鍛模液態模鍛成形過程中熱裂紋形成的主要原因，提出了降低鍛模熱裂紋的幾點措施。 -
This paper analyzes the running problems of a hot die - forging press and presents a diagnos is method to solve the problems
摘要本文就熱模鍛壓力機產生連車故障的原因進行了分析、探討，並由此研究了一種診斷方法，以便徹底排除該故障。 -
By vacuum - electron - beam weld of ti3al and tc11 the technology of hot die forging, and then use different heat treatments, study the influence law of the different degree of deform, different heat treatments to the microstructure and properties
採用熱模鍛技術，通過對tac - 1b 、 tc11進行不同程度的變形、真空電子束焊接，然後採用不同的熱處理工藝，研究熱加工工藝對合金組織，性能的影響規律。 -
What ' s more, the application of tc11 two phase alloys to the compress disk of areoengine alredy is relatively mature, and tc11 alloy may work safely for very long time below 500 c. ti3al matrix alloy and ( a + b ) two phase alloy is connected by weld. the request of the temperature and stress can be satisfied by dual alloy disk with isothermal forged ( or hot die forging )
選用ti _ 3al基合金tac - 1b和tc11兩相鈦合金用焊接工藝連接起來，通過熱模鍛或等溫鍛鍛造和不同的變形熱處理制度，製造出雙合金盤可以滿足溫度、應力對盤件的要求。 -
The 60mn hot die forging hydraulic press, with weight 30 % reduction of the main body compared with the traditional hydraulic press because of plate frame structure designed through new idea by adopting transverse pre - tightening technology mainly embodying the design and manufacturing level of the heavy - duty hydraulic presses at modem times, the first one with independent intellectual property right designed by china itself and a transverse pre - tightening plate - frame hydraulic press with max. tonnage in the world at present
摘要60mn熱模鍛液壓機，採用橫向預緊技術，創新設計了板框式本體結構，與傳統液壓機相比，機械本體重量減少了30 % ，採用的主要技術集中體現了當代大型液壓機設計和製造技術水平，成為中國自行研製的具有自主知識產權的首臺，並且也是目前世界上最大噸位的橫向預緊板框式液壓機。 -
Abstract : in the light of two common failure modes in use, i. e. thermal wear and hot fatigue crack, this paper analyzes the reasons and puts forward the measures to be taken for improving the life of forging die
文摘:針對鍛模在使用過程中常見的兩種失效形式，即熱磨損和熱疲勞裂紋，分析了其產生的原因，並提出了為提高鍛模壽命而應採取的措施。 -
Development and application of environment - friendly hot die forging agent
環保型熱模鍛壓劑的研製及應用 -
The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine
實驗結果表明，經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h ， ac或815 1h + 700 8h ， ac熱處理后，焊接區組織過渡均勻，可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ，而在600拉伸時高於tc11合金，獲得強度、塑性、硬度均令人滿意的綜合性能，且是一條可行的工藝路線。 -
To improve and stabilize the service life of hot - forging die fabricated by cast die steer, the failure modes and mechanism were analyzed
摘要為了穩定和提高精鑄熱鍛的使用壽命，研究了其失效形式和機理。 -
Nakano forging employs a sub press to carry out stamp forging of brass materials, which have superb hot - forging forming characteristics and can be punched in both the horizontal and vertical directions using the horizontal method and the closed die method
熱鍛造成型性優越的黃銅材料在模型鍛造時可通過模架模實現水平及垂直方向進行鉆孔水平式，合模式，可滿足顧客省材，省切割加工的需要，特別是數量越多其特點越明顯。 -
Microstructure simulation in hot die steel after hot forging and simulation software design
熱作模具鋼鍛后組織模擬及軟體設計
分享友人