hydraulic drop 中文意思是什麼

hydraulic drop 解釋
水力落差。

  • hydraulic : adj. 1. 水力的，液力的;用水發動的。2. 液壓的，水壓的。3. 水力學的。4. 【建築】水硬的。adv. -lically
  • drop : n 1 滴；液滴，水滴。2 〈pl 〉 【藥學】滴劑；滴眼藥。3 微量，點滴；一口[杯]酒。4 滴狀物；耳墜；水...
  1. This paper supplied a new way through variable frequency variable speed ( vfvs ) to change its output flow rate and adding a constant - pressure - drop valve, which could solve the defects in hydraulic pressure servo control system, such as low efficiency in control system, short life, poor ability in resisting pollution, low efficiency in driving system and flow rate, pressure pulse. and this way was proved to be effective

    本論文針對傳統伺服控制系統效率不高、元件壽命短、抗污染能力差、驅動系統效率低、存在流量及壓力脈動等缺陷，利用先進的交流變頻調速技術改變液壓泵轉速的容積調速新方法，提出了在液壓系統中加一個定差減壓閥的新思路，較好地解決了液壓伺服系統存在的上述問題。
  2. In this thesis hydraulic experimental studies and theoretical analyses on the vortex - flow drop shaft were conduced and the following results were accomplished : ( 1 ) in the model test some hydraulic characteristics including the shape of air core in the center of the drop shaft, the radial distribution of water flow velocity and the distribution of pressure on the wall of the drop shaft were measured under the condition of high water head above 250m and large discharge above 1400m3 / s. ( 2 ) a kind of computational method for the spiral water flow in the air core region of drop shaft was discussed and applied and the results agree the experimental data well. ( 3 ) the total ratio of energy dissipation in the drop shaft can reach 90 % and the energy dissipation in every region was discussed quantitatively

    本文通過試驗研究與理論分析對旋流式豎井泄洪洞應用於高水頭、大泄流量情況時存在的一些水力學問題進行了研究和探討，取得以下主要成果：一、結合小灣工程導流洞改建，對高水頭（ 252m ） 、大泄流量（ 1400m ~ 3 s ）條件下旋流式豎井中的水流運動特徵進行了比較全面的測量，包括空腔形態、徑向流速分佈及井壁壓強等；二、提出了豎井空腔段螺旋水流水力計算方法，其計算結果與實測值吻合良好；三、利用試驗與計算結果，對旋流式豎井的消能機理進行了探討，對豎井各部分的消能能力有了總體認識；四、對豎井下部消力井的合理井深進行了優化試驗研究，發現消力井合理深度為0 . 9d左右；五、通過試驗研究，歸納出豎井水流總摻氣量估算方法，為導流洞排氣方案的設計提供了參考依據；六、在高水頭、大流量條件下，豎井空腔段下部流速很高，盡管水流螺旋運動引起的離心力可以確保井壁壓強保持正壓，但空化數依然較低，因此豎井的空化空蝕始終是工程界關注的重大問題。
  3. Experiment study on hydraulic condition at the intake of inverted siphon with drop shaft

    豎井式倒虹吸管進水口水力條件的試驗研究
  4. So according to the technology regulation of reclamation engineering, hydraulic calculation must be carried out in the design of final closure. this paper firstly introduces the progression and present situation of reclamation engineering, emphasizing on the features of present reclamation and on the experiences and theories of home and abroad ; using fortran perfects the hydraulic calculation program of the closure and makes the program to meet different conditions ( such as considering flood, the variation of time interval, multi - entrance, multi - reservoir capacity ), and after comparing and analyzing a great deal of schemes, the reasonable computation scheme was brought up ; the interface of the program was carried out by the programming language vb to make the process of calculation become easier and more distinct, so the result can be analyzed and handled more directly ; vb is used in the later management of the result to plot the graphic chart of the isoline of the maximum of hydraulic element ( the velocity of flow, the drop height and the rate of flow ) automatically ; finally it was applied in the reclamation project of dongbidao of fuqing

    本文首先介紹圍海工程的發展進程與國內外圍海的開發現狀，重點介紹了我國目前圍海工程的特點及在圍海工程實踐中積累的經驗和理論；利用fortran語言完善堵口工程龍口水力計算程序，使程序可以滿足圍海工程復雜工況下（如考慮內港洪水、計算時段的變化、多口門、多庫容、多水閘）的龍口水力計算，並進行大量方案的比較和分析，提出合理計算方案；利用面向對象的可視化編程語言vb進行界面開發，使計算過程有良好的人機界面，更直觀地對計算結果進行分析和處理；計算結果的后處理採用vb編程實現龍口水力要素最大值等值線圖的繪制；並運用所編軟體對福建省福清市東壁島圍墾工程進行龍口水力計算，為堵口合龍提供科學依據。
  5. Seawall and sluice are the parts constructed in advance, while final closure is the last part in construction. the hydraulic condition during the final closure process is worse than that during any other processes. and with the compressing of the entrance, the hydraulic condition becomes badly, the drop height of entrance can reach 2 to 3 meter, the maximum velocity of flow even reaches 6 to 8 meter per second and flow condition also becomes complex

    海堤和水閘的修建都是圍海工程先期施工的部分，堵口則是海堤修築的最後階段，堵口合龍成敗關繫到圍海工程成敗，由於此階段所遇到的水力條件十分惡劣，口門落差可達2 3m ，流速最大可達到6 8m / s ，且水流極其復雜，根據我國《圍海工程技術規范》規定圍海堵口必須進行龍口水力計算。
  6. Hydraulic structures - guidelines - part 2 : river bottom protection structures ; drop structures, chutes, cascades, sills

    水工結構.指南.第2部分:河床保護結構.跌水構築物陡
  7. Form for enquiry, quoting and ordering of drop forging plant. hydraulic presses

    落鍛設備的詢價報價和訂貨格式.液壓機
  8. Key issues including water plugging types, waterproof board spreading methods, drop of external water pressure and lining design for resisting hydraulic pressure, etc. were studied, thus the composite waterproof and drainage system to control drainage were put forward, including grouting sphere for water plugging, primary support, grid sysytem for waterproof and drainage and lining to resist hydraulic pressure

    重點就堵水方式、防水板鋪掛形式、外水壓力的折減以及抗水壓襯砌設計等技術問題進行了研究，提出了可通過注漿堵水圈、初期支護、防排水網格和抗水壓襯砌形成綜合防排水體系，它可以達到控制排放的目的。
  9. Because the operation in water hydraulic valves is controlled by flow fluid and the pressure drop results from energy loss of flow fluid past valve channel, the flow state of fluid in valves becomes the most important factor for the operational property of valves

    由於水壓閥是通過控制流體流動來操作系統的，閥的壓降也來自於流體流經閥道時的能量損失，因此閥內的流體流動狀態就成為決定閥操作性能最為重要的因素。
  10. The flow of every pump is inclined to be different in the same side - inlet sump and the poor flow pattern, and then the inlet condition of the pump is not good, which makes the efficiency of the pump drop and causes vibration etc. based on the theses on the hydraulic characteristic of the wenshui road pumping station in the third period shanghai disposal sewage project, the methods were discussed to improve the flow pattern of side - inlet sump, and the measures were put forward to ameliorate the flow pattern in the paper

    對側向進水集水池，一般會出現同池各水泵配水不均勻，池內流態紊亂、水泵吸水條件差，繼而導致水泵效率下降、機組振動等問題。本文結合上海市污水治理三期工程汶水路泵站水力特性研究課題，探討了改善側向進水集水池水力特性的途徑與方法，提出了有效的整流、均流措施。
  11. Preliminary analysis and calculation of liquid metal pb - 17li mhd pressure drop in the blanket for the fds have been presented to evaluate the significance of mhd effect to the thermal - hydraulic design of the blanket

    針對雙冷嬗變核廢物包層液態金屬的流動特徵，進行了mhd壓降的研究計算和數值模擬，進行程序實現分析。
  12. 3. testing all the hydraulic parameters of the sprinkler installed with adjuster such as working pressure, water flux, the range of the sprinkler, intensity of water drop impact, characteristic of water distribution, etc. according to the testing data, we can learn the quantitative relations among the structure of the adjuster, working pressure, diameter of the nozzle, elevation of sprinkler, wind power, velocity of rotation and the range of water

    測試安裝「壓力調節器」后的噴頭的水力性能參數，即工作壓力、流量、射程、水滴的打擊強度、噴灑水分佈特性等。依據所測得的噴頭水力性能參數和射程數據，我們可較清楚的了解「壓力調節器」的結構形式、工作壓力、噴嘴直徑、噴射仰角、風力、旋轉速度和噴頭射程之間的定量關系。
  13. Research on hydraulic transients and operating system for energy - reserve rapid - drop gate of large scale pumping stations

    大型泵站水力過渡過程計算及蓄能式液壓啟閉閘門的研究
  14. The multi - functional blanket for waste transmutation and fuel production has been developed. based on studies for feasibility and reliability of fusion - driven hybrid reactor, the conceptual design of dwtb is presented, especially the analysis activities of liquid metal mhd pressure drop in the fds blanket that is included into thermal - hydraulic analysis

    本論文針對雙冷嬗變核廢物包層設計，從液態金屬磁流體動力學觀點出發，提出與液態金屬mhd效應相關的研究設計概念，並對雙冷嬗變核廢物包層中液態金屬mhd壓降進行分析研究和模擬計算，評價其可行性。
  15. They are suitable in the hydraulic system with high pressure, high flow rate and low pressure drop

    該閥非常適合用於高壓大流量，壓力損失小的系統。
  16. Hydraulic fluid power - filters - evaluation of pressure drop versus flow characteristics

    液壓過濾器壓降流量特性的評定
分享友人
分享到 Line

分享到臉書