hydrostatic load 中文意思是什麼

hydrostatic load 解釋
靜水荷載
  • hydrostatic : adj. 流體靜力（學）的；靜水（學）的。
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  1. 8. a simplified 3 - d natural river flow and sediment transport model is developed based on hydrostatic pressure distribution. the model has been applied to investigate the 3 - d flow and suspended - load transport in nanjing river reach with two branches

    （ 8 ）天然三維水流泥沙簡化數值模型，成功地模擬南京某河段水流運動和多分汊河道水沙計算，結果可靠並滿足精度。
  2. The paper also analyzed that different spindle structures and bearing arrangements influenced load - bearing characteristics of motorized spindle, finally obtained excellent multi - support hydrostatic bearing motorized spindle structure

    分析了不同主軸結構和軸承布置對電主軸承載特性的影響，優選出了的多支承靜壓軸承電主軸結構。
  3. Thermoplastics piping systems. non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings. test method for leakightness under internal hydrostatic pressure without end thrust

    熱塑料管道系統.壓力管和模塑配件的合成橡膠密封環型接合.在無軸向推力時內部流體靜力學壓力下密封性試驗方法
  4. By application navier - stokes equations under the sphere coordinate, the calculation formula of the support load of the oil film of the ball joint coupling based on hydrostatic bearing. support property equation of this ball joint coupling was set up. at same time, the formula of the oil film stiffness was established

    運用球坐標系下的納維-斯拖克斯方程組推導出靜壓支承球鉸副油膜支承反力的求解公式，給出了靜壓支承球鉸副油膜支承特性方程，得出了靜壓支承球鉸副油膜剛度計算公式； 4
  5. Thermoplastics piping systems - non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - test method for leaktightness under internal hydrostatic pressure without end thrust

    熱塑管道系統.壓力管和模塑管件的無端負荷彈性密封環型連接件.在無軸向推力時內部流體靜壓力下密封性的試驗方法
  6. ( 3 ) the contact model is used to simulate the crack. on the basis of project, the evolution of crack opening and crack depth related to loads such as hydrostatic pressure and temperature are studied using numerical simulation approach, and the load effect on the crack evolution is discussed

    （ 3 ）用接觸模型模擬裂縫，結合工程實際，應用數值模擬分析方法研究裂縫開度和開裂深度隨外荷載（水壓、溫度等）的演變規律，分析了裂縫演變的荷載效應。
  7. Thermoplastics piping systems - non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - test method for leaktightness under internal hydrostatic pressure whithout end thrust ; german version en 714 : 1994

    熱塑管道系統.壓力管道和模壓管件之間無末端承載的橡
分享友人
分享到 Line

分享到臉書