inertia resistance 中文意思是什麼

inertia resistance 解釋
慣性阻力
  • inertia : n. 1. 【物理學】慣性，惰性，慣量。2. 不活動，不活潑，遲鈍，惰性。3. 【醫學】無力。adj. -less 無慣性的，無慣量的。
  • resistance : n. 1. 抵抗，反抗，抗拒，抵禦；敵對，抵抗力，反抗力，阻力，【生物學】抗病性。2. 【電學】電阻；阻抗；電阻器。
  1. Drawback occurred in the classical vssmc can be alleviated in the proposed control scheme because of importing the eliminating chatterer. according to the control strategy put forward above, corresponding controller for abs is designed. quarter braking vehicle model with four dof ( including vertical and longitudinal motions of body as well as vertical and spin motions of wheel ) is built considering the effects of wind resistance, longitudinal inertia forces, the vertical dynamics associated with the suspen

    總之，基於車輛動力學建模，提出並探索了幾種實用且具有高魯棒性的變結構、模糊控制策略在abs 、 asr及vdsc系統中的應用，而後開發了abs的ecu原形，採用實時硬體在環模擬技術，對三種模糊控制策略進行了性能模擬。
  2. Finally, it is proved feasible to simulate the road - driving condition of electric bicycle on the testing platform. the collectivity programming of electric bicycle automatic testing system is maken out, including the simulated application strategy and method of road - resistance and wheeling inertia, design principle and evaluation system

    （ 2 ）對電動自行車自動檢測系統設計做出了總體規劃，確定了行駛阻力與轉動慣量的模擬策略和方法，明確了系統設計原則，建立了系統評價體系，運用多級模糊綜合評價模型對各設計方案進行了評價選優。
  3. In order to test resistance parameters and general properties of the idler automatically and continuously, by using " the rotating inertia method " to construct mechanical drive control system, theory of realizing double parameters measurement of the idler was discussed, and by using pressure transducer parts to control the experiment pressure, method of examining the idler was also put forward

    摘要為實現對托輥阻力參數及綜合性能的自動化、連續化的測試，論述了利用理論力學中「轉動慣量法」構建機械傳動控制系統，實現托輥阻力雙參數測量的原理，闡明了採用壓力傳感器部件控制試驗壓力，達到托輥產品在規定壓力下跑合要求的檢測方法。
  4. In the dynamic equation both the viscoelasticity properties of belt, the run resistance, the inertia force of take - up, the belt ' s elastic modulus influented by the deflection of belt and the initial stress have been considered

    所建立模型的動力學方程不僅考慮了輸送帶的粘彈性力學性質、運行阻力、張緊裝置的慣性力和輸送帶撓度變化下的彈性模量，同時也考慮了輸送帶初始張力的影響。
  5. Motor vehicles need energy to accelerate ( overcome inertia ), to push the air out of their way ( aerodynamic drag ), and to overcome the friction from tires, wheels and axles ( rolling resistance )

    帶發動機的車輛需要能量進行加速（克服慣性阻力） ，推開路上的空氣（空氣動力學拖曳力） ，並克服輪胎、車輪和車軸的摩擦力（滾動阻力） 。
  6. For mild channel, it is shown that dynamic term and resistance term deviations caused by the distortion influence model water flow movement more seriously than inertia term do

    分析表明，對于平原河道，動力項和阻力項偏離是主要的，慣性項的偏離對模型水流運動影響較小。
分享友人
分享到 Line

分享到臉書