injection limit 中文意思是什麼

injection limit 解釋
噴吹極限
  • injection : n. 1. 注射。2. 注射劑，注射液，針藥，灌腸（藥）。3. 充滿，注滿。4. 【醫學】充血。5. 【機械工程】噴射。6. 【宇宙空間技術】（衛星等的）入軌，射入軌道，射入軌道的時間[地點]。
  • limit : n. 1. 界限，界線；邊界。2. 極限，限度；限制。3. 〈pl. 〉范圍，范域。4. 限價；限額；賭注限額；獵物限額。vt. 1. 限制，限定。2. 減少。adj. -able
  1. It shows that the injection quantity and the difference of temperature distribute as a parabola which is at the same load, and the minimum of the parabola corresponds to the optimum quantity of injection ( g ). under the condition that the quantity of injected mass, the air speed and the heat quantity is respectively g, v and q, the research demonstrates that the pentium iv chip ' s temperature variation can be controlled under 40c and work normally when the wind speed overpass 1. 5m / s and the power dissipation of the chip is 60w. otherwise this paper calculates the flooding limit of thermosiphon with several different methods

    對其充灌量、散熱量、電子元件（ cpu模擬晶元）表面與環境溫度之差及通風、流速的影響進行了系統的測試，發現充液量與溫差的關系在負荷不變時呈拋物線分佈，其極小值點對應的充液量是最佳充液量g 。在充液量為g時，對風速v 、散熱量q進行的研究表明，當風速超過1 . 5m / s后，奔騰晶元在60w發熱條件下晶元溫度小於40 ，能滿足長期正常工作。
  2. With experiments and theoretical analyzing, we find when the heat discharge is smaller than the entrainment limited, what influences the ability of heat - transmitting of work quality is the quantity of injection and dry limit fluid inventory, the optimum quantity of injection of the three working fluid is 8 ~ 14g ; and the delivering factor that transmission coefficient is determined by capillary limit, not the heat transmission ability of the thermal syphon. therefore, among the three working fluid, acetone is the best. low wind - speed has the obvious function in heat transmission of the thermal syphon

    本文通過實驗研究和理論分析，認為在熱流量小於攜帶極限時，影響工質傳熱能力的是cpu重力熱管的充液量和其乾涸極限，此次所實驗的三種工質，最佳充液量應當在8g ~ 14g ；傳輸因素主要決定普通熱管的毛細極限，而不是重力熱管傳熱能力的決定因素；三種工質中的最佳工質是丙酮；小風速時風速的變化對cpu重力熱管的傳熱有明顯的作用，但在風速大於1m / s以後，風速增加對于cpu重力熱管的傳熱能力的增加效果減緩。
  3. Experiments on the lean blowout limit of cavity flame holder with liquid kerosene fuel on room temperature were conducted with various cavities and injection schemes

    對基於常溫液體煤油燃料的凹腔火焰穩定器的貧油穩焰范圍進行了試驗研究，比較了不同凹腔結構尺寸和不同噴注方式。
  4. It is found that the liquid kerosene of injection upstream cavity could finish the process of atomization and evaporation in short distance, and enter into cavity through convection. aft wall is the primarily area of flame holding in cavity, and the only area when near the lean blowout limit, flame in area of fore wall are spread from it. cavity shear layer in reaction flow angle greatly to the main flow direction, and couldn ’ t reattach to aft wall anymore, it appears great difference in characteristics of cavity flowfield between non - reaction and reaction state

    研究發現:凹腔上游噴注的液體燃料能夠迅速霧化、蒸發，並在較短距離內依靠對流輸運過程進入凹腔內部;凹腔後壁始終是凹腔火焰駐留的主要區域，在貧油極限時，也是唯一區域，並存在明顯的火焰由後壁向前壁的傳播過程;燃燒狀態下的凹腔剪切層以較大角度向下游主流發展，不再附著于凹腔後壁，與冷流中的凹腔流場特徵相差較大。
  5. In agreement with this concept is the additional experimental result that decreasing the mean hydrogen injection velocity increases the stability limit temperature.

    這一概念是與補充試驗的結果相符的，即降低氫的平均噴射速度使穩定性極限溫度增加。
  6. Through adjusting the controlling fuel injection - - regulations of the two injection timings and proportions, an adequate air and fuel charge stratification was produced - we call it quasi - homogenous mixture and the lean burn was successfully realized in a product 4 - valve s. i. engine whose structures are n ' t changed at all. investigations show that twice electronic fuel injection can make the lean limit ( a / f ) increase by 1. 5 - 2 units ; the fuel consumption and exhaust emissions are improved remarkably, in partial load, compared with the product 4 - valve s. i

    研究結果表明：兩次噴油可拓展發動機稀燃極限1 . 5 - 2個空燃比單位，最高達23 . 5 ；發動機燃油消耗同原電噴發動機相比可降低19 . 1 % ；整個空燃比范圍內，經過優化的兩次噴油稀燃的最低油耗較單次噴油稀燃下降6 . 5 %左右，各種排放物機內生成量均有大幅度下降。
  7. It is recommended to conduct injection - production tests under different spacing to decide technical limit spacing according to production well performance

    現場可進行幾種不同井距下的注采試驗，然後根據各種井距下採油井的動態情況來定性判斷低滲透砂巖油藏技術極限井距。
分享友人
分享到 Line

分享到臉書