injector nozzle 中文意思是什麼

injector nozzle 解釋
噴射口
  • injector : n. 1. 注射者；注射器，針管。2. 【機械工程】噴射器，噴注器，噴霧器，噴頭。
  • nozzle : n. 管嘴；噴嘴；〈俚語〉鼻子。 a jet [propelling] nozzle 【火箭】尾噴管。
  1. A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle

    試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。
  2. Dimensions for mounting and connection of injector nozzle

    噴油嘴偶件.型式及連接尺寸
  3. Xud - 9 test method for diesel engine injector nozzle coking test

    柴油機噴嘴結焦試驗方法
  4. Technical system includes the injector and the accelerator subsystem, synchrotron, beam transport, gantry with beam transport and nozzle, treatment couch and control subsystems etc

    技術系統包括用作入射器的加速器、高能加速器（可採用同步?旋加速器） 、射束輸送管、旋轉架質子輸送和射?管口、治療床、管制次系統等。
  5. Petroleum and related products - determination of the shear stability of polymer - containing oils using a diesel injector nozzle

    石油和相關產品.使用柴油注射器噴嘴測定含聚合物油的剪切穩定性
  6. The original pump - line - nozzle injection system was found to be not well suited to alternative fuels. this paper introduces a novel electronically controlled pump - rail - valve - injector fuel injection system

    但液化代用燃料在發動機應用最大的困難是與常規泵-管-嘴噴射系統的不匹配。
  7. Petroleum and related products - determination of the shear stability of polymer - containing oils using a diesel injector nozzle iso 20844 : 2004 ; german version en iso 20844 : 2004

    石油及其相關產品.利用柴油噴射器嘴測定含聚合物油的
  8. The service condition of diesel injector nozzle is introduced, the failure reasons of diesel injector nozzle are mainly analyzed, the quality of diesel injector nozzle is improved and the useful life way of diesel injector nozzle is extended

    摘要介紹了噴油嘴偶件的服役條件，分析了噴油嘴偶件失效的原因，對提高噴油嘴偶件質量和延長噴油嘴偶件使用壽命的途徑進行了探討。
  9. The hot runner series makes the plastics in the hot runner from the nozzle of a plastics injector to the inlet of cavity must be always kept at such a molten state by means of heating that you just pick out the product, there is no need for you to take the condensing stuffs from the injection system as the mould cavity is operated

    說明:熱流道系列用加熱的方法使從注塑機噴嘴到型腔入口為止這一段流道中的塑料一直保持熔融狀態，在開模時只需取出產品，而不必取澆注系統凝料。
  10. The project is funded by the anhui oil pump and oil nozzle factory. the aim of this project is to develop the automatic separation system of injector valve and orifice, based on the pneumatic sensor and the mcu

    本課題來源於安徽油泵油嘴廠，目的是研究一套價格為企業所接受的基於氣動傳感器並以單片機進行數據處理和控制的噴油嘴偶件針閥和針閥體自動測量分選系統。
分享友人
分享到 Line

分享到臉書