inlet temperature 中文意思是什麼

inlet temperature 解釋
進口溫度
  • inlet : n. 1. 進口，入口。2. 【電學】引入，輸入，輸入線。3. 水灣，小港。4. 插入物，鑲嵌物。vt. （inlet, inletting）1. 引進。2. 嵌入，插入。
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. As for the dehumidifying conditions, the condensing rate for the humid air increases with reynolds number but decreases as the inlet temperature of cold water increases

    同時濕盤管的熱傳量及除濕率亦也隨著冰水入口溫度的降低而增加，顯熱比隨著冰水溫度的降低而減小。
  2. For a soil or rock of water - lacked, a heat transfer theoretical model is developed, which is a steady or unsteady, the results show that reservoir temperature, thermal diffusion coefficient, inlet temperature, flow rate of and run time of ground source heat pumps have an effect directly on heat transfer process of dhe. it can deduce that intermit running is favorable for this type of soils and rocks

    對于貧含水地下巖土層建立了穩態與非穩態傳熱的理論模型，分析結果表明，巖土層的熱儲溫度、導溫系數、埋地換熱器進水溫度、流量以及地源熱泵系統的運行時間或開停機比，都對埋地換熱器的傳熱過程產生直接影響，可以推斷，對于該類型巖土層的地源熱泵系統，採用間歇運行將是有利的。
  3. Experimental studies on s1a - 02 gas turbine with water injection into compressor interstage / inlet as well as that on turbocharger self - loop test rig with inlet water injection are introduced. test results are in good accordance with simulation results, wet compression can lower compression work and increase engine power output so engine performance is enhanced, if engine power output is not changed, efficiencies of compressor and this engine become higher and turbine inlet temperature and fuel consumption become lower and if keeping t4 the same as that before wet compression is used, efficiencies become furthermore higher and engine power output increases greatly

    實驗結果和計算結果同樣表明：濕壓縮減少了壓氣機所消耗的壓縮功，增加了燃氣輪機的輸出功率，提高了燃氣輪機性能，如果保持發動機輸出功率恆定，濕壓縮可以提高壓氣機和整個燃氣輪機機組的效率，與此同時，渦輪進口溫度t _ 3 ~ *和燃油消耗率下降；如果保持渦輪排氣溫度t _ 4 ~ *恆定，壓氣機和燃氣輪機機組效率進一步提高，燃氣輪機輸出功率增加。
  4. The sensible heat factors are found to increase with both reynolds number and inlet temperature of cold water

    濕盤管的熱傳量隨著入口風速與鰭片數目的增加而增加，顯熱比及除濕率亦隨著風速增加而增大。
  5. Influence of inlet temperature of cold media on ice - forming processes outside pipes

    冷媒進口溫度對管外結冰過程的影響
  6. The blade inner channel cooling is very important in the design of turbine blade, with the ever - increasing inlet temperature, the new heat transfer enhancement structures of higher performance are demanded. because of the complexity of the flow and heat transfer of the blade inner channel cooling, the numerical modulation is superior to the experiment. this thesis studied the blade inner channel cooling with the method of numerical modulation

    葉片內部通道冷卻在航空發動機葉片的設計中佔有重要的位置，航空發動機進口溫度的增高對其提出了更高的要求。由於葉片內部通道冷卻的流動與傳熱的復雜性，數值模擬較實驗的研究方法有其優越性，本文利用數值模擬的方法對葉片內部通道冷卻進行了研究。
  7. In the last part, an experiential formula for nondimensional thermal stratification height is obtained, which includes inlet temperature t, inlet velocity v, heat transfer of the wall body q and the distance of heat source l. in order to obtain a more realistic result, the ? model is used to simulate the airflow and the buoyancy item is treated by boussinesq hypothesis. the paper investigates the flow field of the displacement ventilation in an office by a numerical method

    兩方程湍流模型為基礎的壁面函數處理方法，對熱浮升力項採用了boussinesq假設，得到了收斂的溫度場、速度場分佈。在此基礎上，給出了熱力分層高度的計算方法，並分析了送風溫度、送風速度、圍護結構傳熱和熱源分佈等因素對熱力分層高度的影響。
  8. Haibo huang ( mechanical engineering ) directed by jianzhong xu cooling techniques in turbine have become more important since the extra high inlet temperature in turbine

    隨著渦輪前溫度的提高，渦輪葉片的冷卻技術變得十分重要。渦輪葉片中流/熱耦合計算成為必不可少的熱環境分析手段。
  9. Thirdly, radiator performance test - bed thermal system control modeling and rule self - organizing fuzzy control simulation were studied. the water supply temperature, radiator inlet temperature, test room temperature based on water temperature regulation, air supply average temperature and test room temperature based on air temperature regulation total five controlled processes transfer function were set. finally, rule self - organizing fuzzy control simulation for two

    通過試驗，辨識了散熱器實驗臺熱工系統中供水溫度、散熱器進水溫度、基於熱水系統調節的測試室溫度、送風平均溫度及基於送風系統調節的測試室溫度共5個被控過程的傳遞函數，並對基於熱水系統調節和基於送風系統調節的測試室溫度響應過程進行了規則自組織模糊控制模擬。
  10. Tit turbine inlet temperature

    機進氣溫度
  11. Great difference in pressure for two flow made pressure wave system and it help to extend the delay time for gas in chamber, which increases combustion effusion. second, to increase combustion effusion, the inlet temperature of air and gas should be enhanced in the range of heat releasing in chemical reaction. third, the first work condition is unburned absolutely and the second work condition is burnt in shear layer of inlet and the end of down wall zone in straight segment

    對于壓力差很大的兩股氣流，所形成的壓縮波系的結構可以增加燃氣駐留時間，提高燃燒穩定性;為了提高擴散燃燒的效率，在保證能放熱的化學反應溫度范圍之內，應適當提高燃氣及空氣的來流入口溫度;燃氣噴嘴應居於燃燒室軸線上，是改進超音速燃燒室結構的一種思路。
  12. The results show that while the mass flow of refrigerant is 1. 85g / s, the inlet temperature of refrigerant is 18. 9, the evaporating pressure is 0. 62mpa, the mass flow of water is 31. 1g / s, and the inlet temperature of water is 36. 9, the refrigerant of miniature evaporator wholly vaporizes in the tube, and the heat transfer rate is 342w. it achieved the demand of design

    經過實驗測試，當製冷劑質量流量為1 . 85g / s ，製冷劑入口溫度為18 . 9 ，蒸發壓力為0 . 62mpa ，水的質量流量為31 . 1g / s ，水的入口溫度為36 . 9 ，此時，螺旋管蒸發器內製冷劑完全蒸發，換熱量342w ，達到了微型蒸發器的預期設計要求。
  13. Furthermore, the impacts of the geometric dimensions of the coils, the inlet temperature and the flow velocity of the secondary fluid on the charge / discharge modes were discussed. a comparison of the total freeze - up and the partial freeze - up has also been made

    研究了載冷劑進口溫度、流速和盤管材料的熱導率對蓄冰盤管傳熱性能的影響，並對完全凍結方式和不完全凍結方式的結冰和融冰過程作了比較。
  14. Air systems are effective for space heating because a heat exchanger is not required and the collector inlet temperature is low throughout the day ( approximately room temperature )

    空氣系統對于空間供熱是有效的，因為熱交換器是不必需的，且收集器的進口溫度全天低（近似室內溫度） 。
  15. The effects of the flow rate, the inlet temperature, the inlet concentration and the system pressure, the temperature of cooling wall and the radius on the features of condensation process with binary ( tfe / nmp ) vapor were gained

    同時，也得出了進口流量、進口溫度、進口濃度、體系壓力、冷卻壁溫和管徑等參數對垂直管內部分膜狀冷凝過程參數分佈的影響規律。
  16. Fresh inlet temperature range which satisfies given error limits is achieved, and the effect of instrumentation precision on accuracy of test results is analyzed by calculating and analyzing uncertainties of sensible effectiveness tests

    通過對顯熱效率測試的不確定度的計算與分析，得出了滿足給定誤差限的新風進口溫度范圍，並分析了儀表精度對測試結果準確度的影響。
  17. At the same time, experimental study on boiling heat transfer by changing mass flow of refrigerant, mass flow of water, and inlet temperature of water was also finished. and then the performance of miniature evaporator was estimated

    本文完成了液單相、兩相熱平衡實驗和阻力特性實驗，研究了製冷劑在管內流動的壓降;同時進行了微型蒸發器流動沸騰實驗，通過改變製冷劑質量流量、水的質量流量、水的進口溫度等，實現了對微型蒸發器的性能評價。
  18. The results show that the water condensation rate increased with increasing air inlet humidity ratio, desiccant inlet concentration and desiccant flow rate, and changed very little with air inlet temperature and desiccant inlet temperature

    結果表明：除濕量隨著空氣濕度、除濕溶液的濃度和除濕溶液的流量的增加而增大，而空氣溫度和溶液溫度對除濕量的影響非常小。
  19. The following is the experimental investigations on solidification process of stearic acid. the influences which the inlet temperature and reynolds number of the cooling water have on the solidification process are presented. figures that display how heat flux change versus time has been drawn and analyzed

    然後是硬脂酸凝固問題的實驗研究，分析了換熱流體進口溫度、換熱流體re數大小對凝固過程的影響，繪制了凝固過程中熱流密度變化曲線，比較了螺旋肋肋寬對強化傳熱效果的影響。
  20. In addition, the variations of the viscous effect with different inlet temperature is studied, the changing law of thrust and thrust efficiency with temperature is analyzed

    其次，變化來流氣體溫度，研究粘性效應的變化，分析推力、推力效率受溫度影響的變化規律。
分享友人
分享到 Line

分享到臉書