inner cone 中文意思是什麼

inner cone 解釋
內層
  • inner : adj （superl innermost inmost）1 內部的 （opp outer）。2 思想的，精神的；內心的，秘密的。n 1 內部...
  • cone : n 1 圓錐，錐形物；錐面；錐體。2 火山錐，圓錐形火山；錐狀地區。3 【植物；植物學】球果，球花。4 風...
  1. The ultrastructure of the merozoites of eimeria tenellawas observed and discribed. the pellicle consist of two layer membranes, the outer membrane was a continous covering enclosing the whole merozoites, while the inner pellicular complex is interrupted at the anterior and the micropore, and thicken to form the polar ring and micropore. there are 24 microtubules under the pellicle of the merozoite which originated from the polar ring, all of them are connected with the polar ring, and extend alongside the inner pellicular complex to the middle of the merozoite. the head of the merozoite consists of a conoid, an apical vesicule and polar ring. the conoid is a hollow truncated cone. the conoid and spical vesicule can stretch and contract. there are three or more rhoptry and a lot of micronemes. the nucleus has nucleolus. and two layer membranes

    利用透射電鏡對柔嫩艾美耳球蟲裂殖子的超微結構進行了觀察描述.柔嫩艾美耳球蟲裂殖子的表膜由外膜和內膜復合體兩層組成，外膜連續，內膜復合體在頭部斷開形成極環，在其它部位斷開形成微孔；裂殖子的膜下微管24根，起始於極環，向後延伸至細胞核處；裂殖子的頭部由頂泡、錐體和極環組成，錐體和頂泡可以伸縮；柔嫩艾美耳球蟲裂殖子棒狀體3個以上，微線數量很多，二者都由電子緻密的結構組成；細胞核位於裂殖子的中後部，外被雙層膜，有電子緻密的核仁和染色質
  2. The renovation methods of the inner cone hole of the bar of boring mill

    加工機車發動機主軸孔用組合鏜桿的有限元分析
  3. For small aperture ejection nozzle, especially to the p serial type that the center hole diameter is 4mm, its center hole and inner cone is always adopting imported numerical control machine to grind

    對于小孔徑的噴油嘴，特別是直徑為4mm的p系列噴油嘴的中孔座面的磨削，一直採用進口的數控磨床加工。
  4. Inner cone distance

    小端錐距
  5. Under the classic automatically control theorist ' s leading, the thesis establishes idiographic practice methods that using closed loop open type numerical control system to reconstruct the old hydraulic injection nozzle center hole and inner cone grinder

    在經典自動控制理論的指導下，制定了使用數控系統的全閉環控制方式來改造液壓中孔座面磨床的具體實施方案。
  6. In the paper, it mainly discusses how through redevelopment technique on the homemade open type numerical control system to successfully reconstruct an old hydraulic injection nozzle center hole and inner cone grinder, and make this declining machine obtain excellent capability

    本文主要論述了在利用即將報廢的液壓中孔座面磨床本體基礎上，使用國產開放型數控系統，經二次開發技術，成功地將其改造成性能優良的數控磨床的具體方法。
  7. You will find that cone - shaped wheels, with their outer rims smaller than the inner one, are used to prevent derailing

    ，因外圈比內圈小，才可以防止出軌。
分享友人
分享到 Line

分享到臉書