inner nozzle 中文意思是什麼
inner nozzle
解釋
內水口-
Low frequency micro - vibration causes the micro - fluid to produce uniform dispersion and injection which carried out a hydrophobization treatment on the inner wall of micro - nozzle, thus eliminated the spontaneous flowing of micro - fluid inside the micro - nozzle due to wet ting effect so as to let the micro - injection be provided with a digitalized and volume controllable character
壓電陶瓷低頻微振動使得微流體產生均勻的離散和噴射；對微噴嘴內壁進行疏水化處理，從而消除微流體由於濕潤作用在微噴嘴內部的自發性流動，使得微噴射具有數字化量可控的特徵。 -
Although a dual - mode scramjet ' s configuration is simple and mainly consists of inlet, combustor and wake nozzle, its working process is complicated, especially in the combustor, involving a lot of subjects, including hypersonic aerodynamics, combustion chemistry, etc. the inner flow of a combustor is three - dimensional and complicated, including the interaction of shock wave, deflagration, vortex and boundary layer, and so on
它涉及到高超聲速空氣動力學、燃燒化學、擴散傳質等多門學科；其內部的實際流動是復雜的三維流動過程，充滿著激波、膨脹波、燃燒波、各種渦系、附面層及其相互之間的干擾，因此，燃燒室問題是整個發動機研究的關鍵所在。 -
For small aperture ejection nozzle, especially to the p serial type that the center hole diameter is 4mm, its center hole and inner cone is always adopting imported numerical control machine to grind
對于小孔徑的噴油嘴，特別是直徑為4mm的p系列噴油嘴的中孔座面的磨削，一直採用進口的數控磨床加工。 -
Hard alloy nozzle : the product is made precisely of hard alloy and enjoys the hardness up to hra90. two terminals and inner hole are all receive mirror surface treatment to ensure enameled wire makes no scrape
產品描述：此產品以超硬合金為材料精密加工而成，其硬度高達hra90以上，此產品兩端及內孔全部為鏡面加工，以保障漆包線不被刮傷。 -
1. instead of old inner - mixed vortex nozzles, improved y - type nozzle is developed. the designing calculation of new nozzle and corresponding air distributed organ are made, and the atomization effect is verified and compared with old one
對原內混式旋流型噴油嘴進行改造，改用y型噴嘴，進行了噴嘴改造的設計計算和相應配風器的改造設計計算，比較和校核了其霧化效果。 -
In order to determine thermal loading and working pressure of nozzle inner contour, the gas was regarded as one dimensional isentropic flow, and temperature field of nozzle was computed based on three - dimension finite element model
將燃氣簡化為一維等熵流以確定噴管內型面所承受的溫度和壓力載荷，基於三維有限元模型，計算了噴管的瞬時溫度場。 -
Under the classic automatically control theorist ' s leading, the thesis establishes idiographic practice methods that using closed loop open type numerical control system to reconstruct the old hydraulic injection nozzle center hole and inner cone grinder
在經典自動控制理論的指導下，制定了使用數控系統的全閉環控制方式來改造液壓中孔座面磨床的具體實施方案。 -
In the paper, it mainly discusses how through redevelopment technique on the homemade open type numerical control system to successfully reconstruct an old hydraulic injection nozzle center hole and inner cone grinder, and make this declining machine obtain excellent capability
本文主要論述了在利用即將報廢的液壓中孔座面磨床本體基礎上，使用國產開放型數控系統，經二次開發技術，成功地將其改造成性能優良的數控磨床的具體方法。 -
According to the rheological properties of melted abs filament during extrusion from fdm ' s nozzle, on the basis of research on extruded filament section shape, the compensation model of ideal contour line is established, and a new technique for compensating inner or outer contour line of workpiece is put forward, which should depend on the real width of extruded filament ( instead of nozzle radius ) and the real dimensional shrinkage of workpiece
根據abs絲從噴頭擠出過程中的流變性能，在研究fdm工藝噴頭擠出絲截面形狀的基礎上，建立了理想輪廓線的補償模型，並提出了根據擠出絲實際寬度（而非噴嘴孔直徑）和零件尺寸實際收縮量補償零件內、外輪廓的新方法，驗證試驗結果表明該補償模型和補償方法正確可行。
分享友人