inner sleeve 中文意思是什麼
inner sleeve
解釋
內套管-
Under the assumption that the inner surface of stator sleeve and outer surface of rotor are smooth, taking the fact into account that the temperature of stator sleeve of evaporation cooling motor keeps almost the same, horizontal evaporation cooling motor is simplified as a physical model of two coaxial sleeves, with outer sleeve ( the stator ) holds still and keep at constant temperature and inner sleeve ( the rotor ) is rotating and heated
本文通過數值和實驗手段研究了臥式蒸發冷卻電機楔形氣隙中的流體流動、傳熱現象。本文在定子套筒和轉子表面光滑的假設下，針對蒸發冷卻電機定子套筒壁面基本恆溫的特點，將實際蒸發冷卻電機簡化為同軸套筒內筒加熱旋轉、外簡靜止定溫的物理模型。 -
The locking mechanism is made up of an inner hole sleeve inside which multiple round leaf blades and round spacers are reciprocally spaced and kinetically sheathed in the blade cases
該鎖芯機構由多個圓形葉片和多個圓形隔片相互間隔活動疊裝在葉片套的內孔套筒中構成。 -
Temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared
對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。 -
Abstract : temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared
文摘:對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。 -
The roundsling inner core is made from high tensile polyester fibre which is wound continuously without a join to provide the maximum possible strength. this core is protected by a tough woven tubular sleeve also made from polyester without side stitch. it serves to protect both the inner core of the sling and the surface of the product which it is lifting
此產品的內層用極抗拉的合成纖維製成，在製作過程中採用不停絞織，無結口，使其具有極強的抗拉力，成空心套筒狀，兩邊無縫痕跡，在吊裝時，對吊帶的裡外層還能起到保護作用。 -
The distribution of the gas - flow speed is measured at a position 1cm away from the outlet ( the end with larger air - gap ). it is illustrated that the gas - flow speed keeps increasing from the out surface of the inner sleeve to the inner surface of the outer sleeve, and then it decreases gradually
測量了楔形氣隙流體出口（大間隙埠）外1厘米處空氣流速大小的分佈，發現空氣流速自轉子（內筒）壁面處開始逐步增大，至定子（外筒）壁面處達到最大值，隨后開始減小。 -
The optimization selection and comparison have been conducted on the ratios of major structural dimensions of ball cage patterned constant speed universal joint namely the ratio between central circle diameter of steel ball and ball diameter, the ratio between outer diameter of universal joint and diameter of graduation circle of inner sleeve spline and the ratio between eccentricity of ball cage patterned constant speed universal joint and central circle radius of ball
對球籠式等速萬向節的主要結構尺寸即鋼球中心圓直徑與鋼球直徑之比、萬向節外徑與內套花鍵分度圓直徑之比，以及球籠式等速萬向節的偏心距與鋼球中心圓半徑之比進行了優化選擇和比較。 -
The hsc - a hydraulic stage cementer features inner closing structure, opening through pressure difference. the closing plug drives the closing sleeve down and then shut circulation ports
型壓差式雙級注水泥器為內關閉式結構，不需投重力塞，通過液體的壓力差打開循環孔，關閉塞帶動關閉套下行關閉循環孔。
分享友人