intake efficiency 中文意思是什麼

intake efficiency 解釋
進氣道效率
  • intake : n 1 吸入，納入，收納。2 進水口 （opp outlet）; 輸入端，（礦井的）進風巷道，通風孔。3 吸氣，進氣。...
  • efficiency : n. 1. 功效。2. 效率；效能；實力，能力。3. 【物理學】性能。
  1. Meanwhile in the condition of high temperature, water vapors can participate in combustion. water gas reaction will happen, which will reduce carbon particle in flame, and reform combustion performance, so improve combustion efficiency. the article developed a kind of technology of water injection into intake ports for 4135g diesel engine, meanwhile designed a suit of water injection system

    同時在高溫條件下，水蒸汽參與燃燒，部分水分子與未完全燃燒的熾熱的炭粒發生水煤氣反應，形成可燃性氣體，從而減少了火焰中的炭粒，提高了油的燃燒程度，改善了燃燒狀況，提高了油的燃燒效率。
  2. For intake system, adopting the resonant intake manifold construction, make use of the intake motive effect to increase volumetric efficiency ; adopt measure to prevent the heat transmit between intake pipe and exhaust pipe, lower the intake air temperature to increase volumetric efficiency

    對于進氣系統，採取諧振進氣的結構措施，利用進氣動力效應來提高進氣充量；採取進、排氣管隔熱措施，降低進氣溫度來提高進氣充量。
  3. The results derived from comparison experiments indicate that various performances of the diesel engine adopting the best project is better than those of the previous intake manifold. especially at the rating, the volumetric efficiency and power increases by about 5 %, exhaust temperature decreases by 50, 4. 3g / kw. h fuel consumption is reduced, o. srb smoke emission is cut down

    試驗表明：該方案與原機進氣系統方案相比，其各項性能指標均有不同程度的改進：在標定點的充量系數和功率提高了將近5 ，排溫下降了50 [ ] ，燃油消耗率減少了4 . 3 [ g kw
  4. The results show that the heat transfer in intake manifold and cylinder has obvious effects on the volume efficiency, while the pipe friction coefficients and bent pressure loss coefficients have less effect

    結果表明，進氣管和氣缸的傳熱對充氣效率的影響較顯著，而管道摩擦系數和彎管壓力損失系數對充氣效率的影響較小。
  5. In this paper, simple reacting flow model in solid - propellant ducted rocket combustor based on eddy break - up model is established. the model is used to simulate the three - dimensional combustion flowfields in an experimental motor. some factors how to affect the combustion efficiency are discussed in the paper, including air intake and gas generator nozzle

    本文基於簡單反應的旋渦分裂模型，建立了固體火箭沖壓發動機補燃室內的湍流燃燒模型，並在該模型下對某實驗發動機進行了三維數值模擬，研究了補燃室設計參數包括進氣道出口設計參數和燃氣發生器噴管設計參數對燃燒效率的影響。
  6. The disposal of the valves and intake manifold structure not only affect fresh air charge but airflow in the cylinder, which immediately affect combustion efficiency and the performance of dynamic, economic and emission. the structure of the air distributing institution has influence on charging efficiency and the noise of engine. the combustion chamber affects compression scale which has great influence on dynamical performance ; f / v which affects the exhaust of hc ; squash area and clearance which have great influence on the intensity of squash

    氣缸蓋的氣門排列方式與氣道結構形式影響進氣充量和氣流在氣缸內的運動，從而影響了燃燒效率，對整機的動力性、經濟性以及排放都有直接的影響；配氣機構的形式影響充氣系數和整機噪聲等；缸蓋燃燒室決定了影響整機動力性能的壓縮比，影響hc排放的f / v和對擠流起決定性作用的擠氣面積以及擠氣間隙，所以燃燒室對整機動力性、經濟性、排放等都有重要的影響；氣缸蓋是整機熱負荷與熱應力最大的部件之一，熱負荷過高將不利於發動機壽命以及可靠性的提高。
  7. The mixing of air and fuel can be improved, d ) adding air distributary valve at exit of air - intake can increase the amount of air bifurcated into the dome region, so the value of combustion efficiency is increased, e ) increasing gas generator nozzle number can improve combustion characteristics in the dome region and produce good condition for combustion progress, f ) when the fuel streams are ejected into the second combustor with a angle, the combustion efficiency is increased, g ) when the speed of fuel streams increased, the intension and temperature of recirculation region is improved

    兩個進氣道在補燃室周向成180度布置，有利於增強燃氣同空氣的摻混； 4在進氣道出口增加空氣分流擋板，有利於增加進入頭部的空氣流量，提高燃燒效率； 5增加燃氣噴管數量能增強燃氣同空氣在頭部的燃燒效果，為燃燒的進行創造良好的條件； 6
  8. Adopting the resonant intake manifold is a simple and effective way by which increases volumetric efficiency in order to improve performance of truck diesel engine

    利用諧振進氣系統來提高車用柴油機的充量系數0 ，從而達到改善其性能的目的，是一種簡單而有效的方法。
  9. When volume efficiency is computed by an engine cycle simulation considering gas flow in intake and exhaust manifold as one - dimensional unsteady flow, improperly given parameters in the simulation may cause an error over 5 %

    摘要採用進排氣管流動為一維非定常模型的發動機循環模擬方法計算充氣效率時，若模型中給定的參數不合適，可能引起充氣效率的計算誤差超過5 % 。
  10. Fuel efficiency and power output and emission of an internal combustion engine can be significantly improved by optimizing intake and exhaust valve timing and duration and lift as speed changes during operation

    改變發動機氣門的開啟相位、持續時間和升程是改善發動機性能，提高熱效率和減少有害排放的一種重要方法。
  11. Or, the project cannot play its due efficiency and even can be discarded in the midway. this will cause the great waste. the water intake of ningxia guhai pumping engineering and the water intake of yuejin channel on yellow river have been moved forward several times because of the silt

    位置選擇適宜，建築規模合理，則可以節省工程投資，達到預期效果；位置選擇不當，則有可能造成該工程不能發揮其應有的功效，甚至會中途廢棄，造成極大的浪費，此現象不乏實例，如寧夏的固海揚水取水口，躍進渠黃河取水口因泥沙淤積就曾幾次前移。
  12. Moreover, the effects of the resonant intake manifold various construction parameters on volumetric efficiency are analyzed in this paper, and the best project is provided for the model 4108q diesel engine

    文中還計算分析了諧振進氣系統各結構參數對充量系數0的影響規律，為lf4108q型柴油機利用諧振進氣系統改善其性能，提供一個最佳方案。
分享友人
分享到 Line

分享到臉書