joint condition time 中文意思是什麼

joint condition time 解釋
接頭期
  • joint : n 1 接合,榫接合處,接合點。2 【解剖學】關節。3 【植物;植物學】節。4 【電學】接頭。5 【建築】接...
  • condition : n 1 狀態,狀況,情形;品質。2 〈pl 〉外界狀況,周圍情形。3 地位,身分。4 條件;【語法】條件子句。...
  • time : n 1 時,時間,時日,歲月。2 時候,時刻;期間;時節,季節;〈常pl 〉時期,年代,時代; 〈the time ...
  1. And it investigates the appearance condition ( including joint, crack, eroding, corrosion, braking pole device rupture, crane - girder ' s gnawing railway and so on ) of the whole crane - girder system on the spot, at the same time, it also actually examines the stress of the beam, chemical ingredient, distortion and railway excursion, etc. through sampling, and based on the actually examined results, it checks and calculates the carrying capacity of crane - girder system. then, based on the investigating on the spot and the calculated result, it discusses the mechanism of fatigue failure of the upper part of welded steel crane - girder, analyses the reason of steel crane - girder in the high - frequency emerging the fatigue crack, institutes the strengthened method of damaged steel crane - girder of accurate packing up workshop of the primary mill plant. finally, it presents some advice and suggestions for the repairing and strengthening method of fatigue crack of upper part of steel crane - girder in the high - frequency

    針對包鋼初軋廠精整車間鋼吊車樑上部區域出現裂縫這一問題,本文首先綜述了國內外關于焊接鋼吊車樑上部區域疲勞裂縫的研究現狀;其次對整個吊車梁系統的外觀情況(包括連接、裂縫、腐蝕、銹蝕、制動桿件斷裂、吊車啃軌等)進行了現場調查,抽樣實測了梁的應力、化學成分、變形及軌道偏移等,根據實測結果,對吊車梁系統的承載能力進行了驗算;然後,根據現場調查及計算結果,探討了焊接鋼吊車樑上部區域疲勞破壞的機理,分析了重級工作制鋼吊車梁出現疲勞裂縫的原因,制定了初軋廠精整車間破損鋼吊車梁的加固方案;最後就重級工作制鋼吊車樑上部區域出現疲勞裂縫的修復與加固方案提出了一些意見和建議。
  2. The disease in jaw surface will be drop the bite force ; the bite force in the patient who disease in temporal jaw joint descent obviously than normal person ; serious mistake in join deformity, the acute damage in the area arthritis can also drop the bite force evidently ; compare to normal children, wenneberg fund that the bite force lower and the duration of the biggest bite force shorter in the children who fall ill of the chronic arthritis ; the bite force also be used in appraise of the recovery condition in surgical operation 、 disorder in jaw arthritis and the serious bone offset in bite lopsided etc. some materials, it will be produce polarization phenomenon inside when suffered some force in certain direction, at the same time, it produce opposite electric charge in two of the surface ; and resume to the station of on - electrification when removed the outside force ; change the direction of the outside force, the polarity of the electric charge also be changed, this kind of phenomenon is called as “ piezoelectric effect ”

    本文設計了石英晶體壓電傳感器,以它作為傳感元件把咬合力信號轉變成電信號;利用ts5860型準靜態電荷放大器把傳感器的電荷信號轉變成電壓信號;選用usb7822數據採集卡,編寫該數據採集卡的驅動程序,採集該電壓信號並送到計算機里;編寫labview程序對該信號進行處理,得出咬合力值和咬合力曲線,並把測量結果以電子表格的形式保存,以便做進一步的分析和研究。通過對該測量儀的靜態標定、動態標定、溫度漂移標定以及實際測量試驗,證實了本測量儀具有較高的靈敏度、受動態力和溫度變化的影響比較小、能實時地顯示咬合力曲線和較準確地顯示咬合力值,滿足了咬合力測量的要求。
  3. Cdma has become the main technology of the third generation mobiletelecommunication. many users in cdma system are distinguished by differentspread sequences and have the same time chip and frequency unlike in theconventional tdma system or fdma system. but the practical spread sequences cannot reach the ideal condition, the correlation function equals zero, so that it will causethe multiple access interference ( mai ) when lots of people are communicating. multi - user detection ( mud ) makes joint detection on the received signals by makingfull use of the information of all users ’, which relaxes mai and increases the capacityof system

    Cdma技術已經成為第三代移動通信系統中的主流技術,它與傳統的fdma 、 tdma不同,在cdma系統中多個用戶均佔用同一時隙、同一頻隙,所不同的是選取的地址碼不同,而實際選用的地址碼間的互相關函數又不可能全部達到理想狀態的全為零,因而造成了多個用戶同時通信時,必然要產生多址干擾。
  4. The characteristics about the magnitude and distribution of stress, the width and depth of joint and time sequence of joint opening are compared on condition of different traveling wave directions. the difference between general uniform wave input and traveling wave input is also compared

    分析了分縫壩行波地震輸入的地震響應,比較了常規均勻輸入和行波輸入,行波不同輸入方向對應力的大小和分佈,縫的張合深度和寬度、縫的張合時序等諸多方面的表現特性。
分享友人