joint pin 中文意思是什麼

joint pin 解釋
連接銷。

  • joint : n 1 接合，榫接合處，接合點。2 【解剖學】關節。3 【植物；植物學】節。4 【電學】接頭。5 【建築】接...
  • pin : PIN ＝personal identification number 個人標識號〈自動提款卡等的個人密碼〉。n 1 別針，扣針，飾針；...
  1. Accurate simulation of switch circuit is needed in pin switch design, while limited by assembling techniques, serial resonance and channel inter - coupling exist in the common joint that bring a lot of difficulties for simulation. 2 - dementions simulation software can not establish accurate circuit mode for pin diode switch which gives simulation error, and it costs much more time with 3 - dementation simulation software, which is not applicable in practice for pin switch design

    Pin開關的設計中需要對開關電路進行準確模擬，然而高頻、寬帶、多擲pin開關受裝配工藝的限制，開關公共結點附近存在著串聯諧振和相互耦合，給pin開關的準確模擬帶來了困難:二維模擬軟體很難對電路進行準確建模，模擬誤差較大;三維模擬軟體耗時過長，難以在實際設計中應用。
  2. Direct connect vias conduct so much heat away from the pin and into the plane that high temperature or long soldering time may be required to complete the joint - thermal damage could occur to both the board and the component from soldering or desoldering

    在焊接時，直接連接的過孔會通過引腳把大量的熱傳導至內電層，因此完成焊接就需要很高的溫度或者延長焊接時間，這就會導致在焊接或拆焊時發生電路板或元件的損壞。
  3. Dental extraction forceps - screw and pin joint types

    拔牙鉗.第1部分:螺釘和鉸鏈接合型
  4. Dental extraction forceps. part 1 : screw and pin joint types

    拔牙鉗.第1部分:螺釘和鉸接型
  5. Dental extraction forceps - part 1 : screw and pin joint types iso 9173 - 1 : 1991 ; german version en iso 9173 - 1 : 1995

    拔牙鉗.第1部分:螺釘和鉸鏈接合型
  6. Situated at miu keng in ping che, this monastery was formerly called cheung sang nunnery, and was probably first constructed in 1789 as a joint effort of six villages in ta kwu ling area, namely loi tung, man uk pin, and the alliance of ping yuen hap heung which consisted of ping yeung, nga yui ha, wo keng shan and ping che

    長山古寺位於禾徑山廟徑，原稱長生庵，約於一七八九年由打鼓嶺區的萊洞、萬屋邊和坪源合鄉約（包括坪洋、瓦下、禾徑山及坪? ）六條村落共同興建。廟內供奉佛祖、觀音及地藏王。
  7. Da traders specializes in accessory, battery, bolt and nut, brake shoe, cable camshaft, clutch and parts, c v joint, cylinders, fastener, fuel system, horn, ignition coil, lamp, mirror, motorcycle parts, oil seal, piston / ring / pin, relay, shock oxygen, shock absorber, sleeve, spark plug, starter, valve / guide / seat, wheel hub bearing / unit

    該貿易公司主營螺栓和螺母，火花塞，輪轂軸承，附件，電池，剎車蹄，線束，凸輪軸，離合器，萬向節，喇叭，點火線圈，車燈，車鏡，摩托車配件，油封，活塞，活塞環，繼電器，減震器， ，起動器，氣門座圈，氣門導管。
  8. The equilibrium path is traced using the arc - length scheme with the rigid - pin - joint model in which the spatial beam elements are used in single - layer parts and spatial truss elements are used in the double - layer parts. thus the stability behavior is summarized and the critical load is obtained. 2

    本文採用鋼、鉸接模型，即單層部分採用空間梁單元，雙層部分採用空間桿單元，應用弧長法跟蹤了網殼結構的平衡路徑，總結了此類網殼結構的失穩規律，並且得出了結構由單層過渡到雙層時臨界荷載的變化規律。
分享友人
分享到 Line

分享到臉書