leaf spring model 中文意思是什麼

leaf spring model 解釋
板簧模型
  • leaf : n （pl leaves）1 葉；〈集合詞〉葉子；茶葉，煙葉。2 花瓣。3 （書刊等的）一張（兩面）。4 金屬薄片，...
  • spring : n 1 春季，春天。2 青春；初期。3 〈pl 〉大潮時期。4 泉。5 源頭，水源，根源，本源；發生；動機，原動...
  • model : n 1 模型，雛型；原型；設計圖；模範；（畫家、雕刻家的）模特兒；樣板。2 典型，模範。3 （女服裝店僱...
  1. In this paper, truck ride performance models were founded based on vehicle dynamic. by comparing the different quarter - car and half - car model which founded by taking the trunnion suspension leaf spring as a whole body and separating the trunnion suspension leaf spring into two dynamic equivalent parts, we gained a more reasonable simplified model which comply with the factual performance

    本文根據汽車動力學原理建立平順性動力學模型，通過對平衡懸架彈簧作為整體的車輛模型和平衡懸架彈簧分開等效處理的1 / 4 、 1 / 2車輛模型作了比較分析，得到與實際情況比較符合的簡化模型。
  2. And the displacement control of the leaf spring center was transferred to the displacement at load point. then after the load step options configuration, the leaf spring stress circulation under cycle loadings was calculated. the model was validated by the result compare between the rigid extracted from the simulation results and the one out of the rigid test of the leaf spring

    使用加載頭和簧片的接觸行為來模擬加載狀況，並將對簧片中心的變形控制轉換為對加載點的位移約束，然後利用載荷步選項配置完成一個載荷循環，由此計算出加載階段下鋼板彈簧內部的應力循環。
  3. The fea assembly model was built according to the distortion of the leaf spring in the former phase in ansys apdl. the load case was simulated with contact of loading head and leaf spring

    根據裝配階段各簧片的變形情況，並利用裝配階段所建模型的參數化語言程序建立鋼板彈簧總成的有限元模型。
  4. The study and design on the full automation inserting dynamic and static spring leaf machine applicant : zheng tianlai supervisor : associate professor hu guoqing the labour denseness model was adopted in the most of relay production lines presently inland, which makes the inserting force of the spring - leaves uneven and affects the tangent resistance, so the artificial factor of the product is serious, and the stability is bad

    目前國內繼電器生產中大多採用勞動密集型，繼電器簧片的插入力大小不均勻，影響接觸電阻，所以產品質量人為因素很重，穩定性差。廈門宏發電聲有限公司繼電器生產的簧片插入工序是雇傭大量的工人進行操作，產品的質量無法保證。
  5. The stress result of assembly process and loading process was exchanged with the ansys special function on external data file. and the stress of leaf spring under virtual condition was calculated by the operation of array vectors of model results, which were generated from the external data file

    通過外部文件完成裝配階段向加載階段跨模型的應力結果數據的傳遞，然後在加載階段模型中進行兩階段模型應力數據的合成運算，得到鋼板彈簧實際工況下的完整應力循環。
分享友人
分享到 Line

分享到臉書