line of fracture 中文意思是什麼

line of fracture 解釋
斷裂線
  • line : n 1 線；繩索；釣絲；測深度用繩，捲尺。 a fishing line 釣魚線。 be clever with rod and line 會釣魚...
  • of : OF ＝Old French 古法語。
  • fracture : vt. ,vi. （使）破裂；（使）折斷；（使）斷裂。n. 1. 破裂，折斷，斷裂。2. 裂痕，裂縫，裂面。3. 【醫學】挫傷，骨折。4. 【礦物】斷口；【地質學；地理學】斷層。
  1. Research about ctod and its components 8 ", " shows that the direction angle of ctod vector is identical with the fracture angle of void - mode fracture, which is obtained through experiments, and it is also identical with the result got by peak value line of stress triaxiality. besides, 8 i " was compare with vgc as criterion for initiation of void - mode fracture

    對裂紋尖端張開位移ctod及其張開型分量~ 1和剪切型分量~ 11的分析表明，在試件發生韌窩型斷裂時，按照圓弧裂紋中ctod矢量的垂直方向預測的斷裂角與試驗測得的斷裂角符合較好，與三軸度脊線預計的結果也比較一致。
  2. Thermal activation analysis of dynamic fracture of pipe line steel x

    70管線鋼動態斷裂的熱激活實驗與分析
  3. In short, the analysis of arc - tip fracture shows that : the initiation of void - mode fracture can be judged by vgc criterion, or by j ". according to sx criterion ; fracture direction of void - mode fracture can be determined by ctod and peak value line of stress triaxiality. the mesomechanics mechanism of shear - mode fracture need further study, and analysis found direction of plastic belt is consistent with the direction of shear - mode fracture

    綜上所述，本文通過對圓弧尖端裂紋的分析表明：對于韌窩型斷裂的起裂，可以依據-復合型斷裂的sx準則按照i ~ 1來預測起裂載荷，也可用v _ （ gc ）判據來預測起裂載荷，二者結果相近；對于韌窩型斷裂的斷裂角，用ctod矢量方向和三軸度脊線方向判斷均和試驗結果基本。
  4. The dcb ( double cantilever beam ) met hod to test the interlaminar toughness of fabric - reinforced laminates and the modified compliance calibration method ( mcc ) were adopted in this research. the double cantilever beam ( dcb ) test was executed for stitched laminates to evaluate the interlaminar fracture toughness. the stitch parameters ( stitch line spacing and pitch spacing ) were changed and their effects on interlaminar fracture toughness were examined by means of dcb test by using improved insert type loading fixture

    試驗中採用改進的插入型夾具、雙懸臂梁dcb （ doublecantileverbeam ）試驗方法，測試了載荷?試樣開口位移曲線，依據改進的柔度梁方法（ modifiedcompliancecalibrationmethod （ mcc ） ）計算出了各個試樣的層間斷裂韌性（ r曲線）及層間斷裂韌性的平均值，闡明了縫合工藝參數與層間斷裂韌性（ g _ （ ic ） ）間的關系，以拉伸與彎曲強度為約束條件，以層間斷裂韌性值為目標優化了縫合工藝。
  5. The thesis studied the change of stress triaxiality in the four - point curved beam made in 16mnr with arc - tip crack and its important effect. in the beam, the points of peak value of stress triaxiality distribute along a line, whose direction is well consistent with the fracture direction got by experiment when so > 3mm

    在圓弧裂紋試件中，裂尖附近的三軸度較高的點呈脊線分佈，按照脊線分佈擬合計算得到的三軸度脊線夾角在偏心距so 3mm時與試驗測得的斷裂角符合較好，這種情況下試件發生的是韌窩型斷裂。
  6. This paper presents a method to calculate elastodynamic fracture parameters of surface crack by using the elastic line - spring model combined with perfect ansys software. the main content includes : the traditional line - spring model which is used in the static analysis of surface crack is extended to the dynamic case, the corresponding constitutive relations are derived and combined with the software ansys, and then the corresponding computational technique is formulated

    本文將線彈簧模型與有限元軟體ansys相結合，對彈性表面裂紋的動態斷裂參量進行了研究，所進行的工作主要有：將傳統的用於靜態表面裂紋分析的線彈簧模型推廣用於動態斷裂分析，導出了相應的線彈簧本構關系，並與有限元（ ansys ）相結合，建立了相應的求解技術。
分享友人
分享到 Line

分享到臉書