loading spring 中文意思是什麼

loading spring 解釋
負荷彈簧
  • loading : n. 1. 裝貨。2. 裝載量；重量；載荷；（船隻等的）貨載。 3. 填充物，填料。4. 額外人壽保險。
  • spring : n 1 春季，春天。2 青春；初期。3 〈pl 〉大潮時期。4 泉。5 源頭，水源，根源，本源；發生；動機，原動...
  1. This paper introduces the ball lapping model of spring - loading lap tools for the four shafts ball - lapping machine and explains the small tendence mechanism of the ball roundness error using the effets of cutting high points and homogenization lapping error

    摘要從建立四軸球體研磨機彈簧加壓球體研磨的力學模型入手，運用高點切削作用機制和誤差均勻化效應，解釋了球體圓度誤差趨小化研磨機理。
  2. Standard test methods for bend testing of metallic flat materials for spring applications involving static loading

    涉及靜負載的彈簧用金屬板材彎曲試驗的方法
  3. The backdrilled hole can be offset or angular to the spring ' s natural center line and exploits the spring ' s natural tendency to straighten, generating a sound side loading between plunger and barrel at all times

    后鉆孔可以偏離彈簧自然中心線，或與中心線呈一個角度，利用彈簧的自然趨勢伸直，在頂針和客體之間始終形成一個可觀的側作用力。
  4. ( 3 ) in order to solve the negative stiffness problem in structural numerical analysis, the multi - spring method is set forth and its general iterative equations are deduced. several loading

    （ 3 ）為解決結構的負剛度問題提出了多維虛設彈簧法的概念，並對多維虛設彈簧法求解的一般迭代格式進行推導。
  5. It is achieved the common work of pile - soil - structure on nsas by using nonlinear bars from single pile calculation as the structure boundaries. the results show that under some 3 - d loading conditions, significant error can be induced due to the nonlinear characteristic of pile, simply using a nonlinear spring from single pile calculation as the structure boundaries

    在三維受力狀態下，由於樁周土的非線性，迭加原理不再適合，而目前許多有限元程序只是簡單地把單樁計算得到樁頭等效非線性彈簧作為結構的邊界條件，這樣將導致出現比較大的偏差。
  6. If the pipe needs shock absorption or shockproof, shockproof hanger or support should be selected. the load should be equal to the loading capacity and rigidity of the shockproof spring hanger or rubber hanger

    3管道需要減震防震時，應選用防震吊掛或支座，支承的荷載應與防震用彈簧或橡膠的支承能力和剛度相匹配。
  7. Based on the reasonable relationship of bond - slip, by using nonlinear spring element simulating bond - slip model in columns, three - dimensional finite analysis for eccentric loading column was done with the two cases including considering and not considering the bond - slip performance between steel shape and concrete. and then the simulation results were compared with experimental results, which concluded

    在合理的粘結滑移本構關系的基礎上，採用非線性彈簧單元對柱中的粘結滑移進行數值模擬，分別按考慮和不考慮型鋼與混凝土之間的滑移兩種情況進行了三維有限元分析，與試驗結果進行了分析比較，基本模擬出了構件受力性能和破環特徵。
  8. The fea assembly model was built according to the distortion of the leaf spring in the former phase in ansys apdl. the load case was simulated with contact of loading head and leaf spring

    根據裝配階段各簧片的變形情況，並利用裝配階段所建模型的參數化語言程序建立鋼板彈簧總成的有限元模型。
  9. Test methods for bend testing of metallic flat materials for spring applications involving static loading

    靜載彈簧用金屬板材彎曲試驗方法
  10. Because of the sliding at the loading node, this special loading condition can be simulated by contact between the loading head and leaf spring

    並且採用加載頭和簧片間的接觸行為能較準確的模擬出加載點存在著滑移狀況的這種特殊的加載形式。
  11. The stress result of assembly process and loading process was exchanged with the ansys special function on external data file. and the stress of leaf spring under virtual condition was calculated by the operation of array vectors of model results, which were generated from the external data file

    通過外部文件完成裝配階段向加載階段跨模型的應力結果數據的傳遞，然後在加載階段模型中進行兩階段模型應力數據的合成運算，得到鋼板彈簧實際工況下的完整應力循環。
分享友人
分享到 Line

分享到臉書