loads analysis 中文意思是什麼
loads analysis
解釋
載荷分析, 載荷計算-
There are certain difficulties in studying the failure process of frangible materials such as concrete, rock, etc which are caused by dynamic loads such as collision, earthquake, exploding, etc by those current exited numerical methods like finite element method etc. so in order to solve such a problem we should introduce certain new numerical analysis method
現存的一些數值方法如有限元法等在研究混凝土、巖石等脆性材料在沖擊、爆破、地震等動荷載作用下的破壞過程問題中存在著一定的困難。因此，對於此類問題需要新的數值分析方法。 -
Based on the close analysis of the influence factors of the vertical bearing capacity, circular aperture extension theory is employed to establish the computing formulas for the pile vertical stress and the foundation vertical bearing capacity, respectively. moreover, with analyzing the features of the calculation parameters such as materials of gunite mortar, jet pressure, diameter of the jet pipe, pile length, pile layout, a design theory for chemical churning pile composite foundation is proposed. then, the variation of the pipe deformation with loads, the deformation coordination of pile and soil are studied
在此基礎上深入探討了旋噴樁的樁土受力特性及其復合地基的加固機理，從影響旋噴樁復合地基豎向承載力的因素入手，基於圓孔擴張理論給出了樁體豎向應力及旋噴樁復合地基的豎向承載力計算公式;通過對噴射漿液、噴射壓力選取、噴射直徑估算、樁長及樁位設計等各種計算參數的深入分析和研究，提出了一套相應的旋噴樁復合地基設計計算方法;通過計算分析，深入探討了旋噴樁復合地基變形隨荷載變化規律、樁和樁間土變形協調關系、樁土應力比及復合地基壓縮模量的確定，並提出相應的設計方法和修正參數;此外，結合工程應用，對旋噴樁復合地基的施工技術及其現場質量檢測方法進行了較全面的探討。 -
This thesis also introduces some kinds of the jointing of cable and membrane strucfores. an open - air palestra has been designed in this thesis. the force density method has been used to analyze the shape, and the nonlinear finite method has been used to analysis the loads
最後，本文還採用文中推導的離散方法，通過力密度法對某風雨操場進行形態分析，並通過將找形結果用非線性有限元法在無荷載狀態下計算結構的應力，結果表明本文推導的方法找形精度是足夠高的。 -
Analysis of the vibration and extreme strength of very large pontoon under extreme wave loads
極值波浪作用下大型浮碼頭振動與極限強度分析 -
Based on modal analysis of piezoelectric smart laminated plates, an fem based inverse algorithm of the time history of impact loads by piezoelectric modal respondence is presented
摘要基於對智能層合板結構的模態分析，提出由結構的壓電模態響應反演瞬態荷載時間歷程的有限元方法。 -
It is an inelastic analysis during the linear monotony loads. it can show the actual yield mechanism and the appearance sequence of the hinge, find out the weakness of the structure and gain the pushover figure ( floor - shear diagram and element - shear diagram )
進而揭示出在罕遇地震作用下結構實際的屈服機制，各塑性鉸的出現順序，找出結構的薄弱環節，確認結構設計中「強柱弱梁」的設計原則，得出push - over圖形（層剪力圖形及構件剪力圖形） 。 -
This article gives the subsistent ability and the analysis result of intensity after repair in the open field airplane composite material structure by research the intensity, rigid and repair problem under a axis compress loads on a typical three stiffened composite laminate which has a penetrability crack ( a scatter damage ) by a shrapnel
本文通過飛機典型復合材料三加筋層壓板結構在被彈片劃開一穿透性切口（離散源損傷）后，在軸向壓縮載荷作用下所產生的強度、剛度以及修理問題展開了技術研究及探討，給出軍機復合材料加筋板在彈擊後生存力以及外場修理后強度恢復分析結果。 -
And gave priority to the eular - bernonulli beam model, the simply and convenient analytical resolution for the response of the pipelines under dynamical traffic loads through the impulse function and the congruence method of the vibration form and so on. during the analysis of the chanmical results of the pipelines, the randomicity of the output of the pipelines response was taken into accout. so the stochastic process method was applied to describe the probability characters of the pipelines response, which made the results truer, more veracious
本文採用eular - bernonulli梁模型和tomosimko梁模型對動力下kelvin粘彈性地基中管道固有振動性狀進行了分析，提出了各力學結果描述的解析式；並以eular - bernonulli梁模型為主，基於脈沖函數、振型迭加法等對管道在動力交通荷載作用下的管道響應問題提出簡單便捷的解析演算法；在管道受力結果的分析中，考慮管道響應輸出的隨機性，將管道響應用隨機過程來描述其概率特徵，使得結果描述更加真實準確。 -
For loads analysis, a new method considering the effect of meterial main axia is proposed using fem
對于靜力分析，本文提出了全新的考慮膜材主軸方向的非線性有限元法。 -
Failure analysis of two hybrid bearing balls under heavy loads and extremely low temperature conditions
超低溫重載工況下陶瓷球失效分析 -
Taken the bank spillway at yubeishan reservoir as an example, the water loads acted on the spillway, such as static water pressure, dynamic water pressure, shear stress on the surface of the step and so on, are calculated, which can provide evidence to the stability analysis of the dam slope and slope protection
並以萬縣魚背山水庫岸邊溢洪道為例，計算了溢洪道上所受的水流荷載及其分佈，為土石壩坡和護面的穩定分析提供了依據。通過計算證實了既使在較大的單寬流量下，緩坡上的階梯仍有較高的消能率。 -
The work in this thesis mainly includes following parts : 1. as for box girder cross section, the three - bar stimulation method under typical loads and supports has been introduced. the force and stress formulae for flanges have been derived from the three - bar method. by reasonable simplification for multi - cell box girder, the three - bar method has been applied in multi - cell box girder ' s shear lag analysis
對于箱形截面主梁，本文介紹了三桿比擬法上、下翼板中比擬桿的計算公式，以及在典型荷載和支承的情況下翼板內各桿的應力計算公式，並對多箱式主梁截面進行合理簡化，使三桿比擬法應用於多室箱梁的剪力滯分析。 -
But during the 1994 northridge earthquke and 1995 hyogoken - nanbu earthquke, many steel beani - to - column connections were damaged which indicated that cognition on the capacity of this type of joints was rather inadequate. in order to avoid similar damages in the future, analysis on response of beam - to - column connections under cyclic loads is not only significant from the theoretical aspect, but also important in practice
然而， 1994年美國northridge地震和1995年日本的阪神地震中，大量鋼框架樑柱連接發生破壞，顯示出人們對于剛性樑柱連接的受力性能和破壞機理認識還相當不足。為了避免人員傷亡和經濟損失，對鋼框架樑柱連接研究其在循環荷載作用下的反應，不僅具有重要的理論意義，更具有重大的工程實用價值。 -
Considering special form of the boiler frame, the reconstruction and enforcement method, in addition dynamic analysis are given by particular steps : establishment of the model of boiler steel frame, determination of earthquake loads and distribution form, and anti - side force system for the frame to model and analyze, involving loads on the frame and above it, earthquake loads, damping, sway control installation, hanging bar and plate beam
考慮鍋爐構架鋼結構的特殊形式，研究並提出了電站鍋爐鋼結構改造加固研究方法，及動力分析的具體步驟：建立了鍋爐鋼結構動力分析模型、地震荷載分析方法、建立了鍋爐鋼結構布置型式、及整個鍋爐鋼構架抗側力體系模擬分析方法。具體包括：鋼構架本體及構架上荷載、地震載荷與阻尼系數確定、制晃裝置確定、吊桿與大板梁簡化。 -
The main research is below : ( 1 ) the influence to intensity and rigid with corner angle ( 60, 75 and 90 degree ) of crack and the board axes ( 2 ) do a fem stress / strain and crack growth simulation analysis when the corner angle of crack and the board axes is 60 degree ( 3 ) do a intensity resume analysis for the structure which is repaired with a titanium patch in a mechanical way when the corner angle of crack and the board axes is 60 degree through simulation analysis for three failure criterion, we have : ( 1 ) in 60, damage extend quickly with damage analysis in hashin criterion ; it is slower for analysis in maximum stress or hashin - rotem criterion. ( 2 ) in special term ( physical condition incision, shape or maximum load ) the compression strength of the stiffened plate will decline 45 % ~ 50 % under compression loads
通過採用三個不同損傷判據的數值模擬模擬，得到如下結論： （ 1 ）在60時，用hashin判據進行的損傷分析，損傷擴展較快；最大應力及hashin - rotem判據進行的損傷分析，損傷擴展基本相當，且較慢； （ 2 ）在所給加筋板的物理條件、切口大小及形狀、最大載荷等一定的條件下，該加筋板在壓縮載荷作用下，其壓縮強度下降了45 50 ； （ 3 ）在本文提及到的機械連接修理方法以及載荷條件下，修理后的結構強度恢復能夠滿足戰時要求。 -
Buildings in german earthquake areas - design loads, analysis and structural design of buildings
德國地震區建築物.設計載荷分析和建築物結構設計 -
In this paper, the author combines the theory analysis with the experiment research method, and discusses the seismic behaviours, 3d elaborate finite element analysis and simplified model analysis of a kind of multi - function tall building - " sub - shearwall supported by frame ", which is applied widely today. the main contents are as follows : in order to observe the failure process and the earthquake response of the complex structure, and to analysis the seismic behaviour of the structural system and structural members, a 1 / 20 cement mortor model of a complex tall - building which is about to be built was producted and the shaking table test of this model under 26 sorts of earthquake loads was made. using sap2000 finite element analysis program, a 3d analysis model was built in computer, and the elastic time - history analysis of the model was done
本文採用理論分析和試驗研究相結合的方法，研究了目前應用較多的綜合性大廈? ?框支分區剪力墻高層商住樓的抗震性能及空間精細分析和簡化分析方法，主要內容為以下幾方面：對一擬建的復雜高層建築結構，採用1 20比例的空間整體模型，進行了26種工況下的模擬地震振動臺試驗，觀察了結構的破壞過程和地震反應，分析了結構及構件的抗震性能；建立了結構的精細空間模型，利用sap2000n大型有限元分析程序對結構進行了彈性時程分析；通過有限元分析與試驗結果的對比，對結構的抗震性能和抗震能力做出綜合評價，認為該結構由於轉換層上部去掉部分樓板，既可滿足建築設計的通風、採光等要求，又可達到協調結構轉換層上、下樓層抗側剛度的效果，是一種較理想的有多道抗震防線的結構型式。 -
On the basic theory of transfer heat, tribology of rolling bearings and rotor dynamics, taking gdz48a electrospindle as an example, the paper puts forward the spindle bearing ' s quasi - dynamics analysis model with the influences of the friction heat and preloadings analyzes the friction moment, velocities, contact loads, friction heat and stiffness and studies the influences of the friction heat, structure and application parameters on the speed and dynamics
本文以傳熱學、滾動軸承摩擦學和轉子動力學為理論基礎，以gdz48a型電主軸為例，建立了考慮摩擦熱和預緊方式影響的主軸軸承擬動力學分析模型，分析了軸承的摩擦力矩、運動、載荷和剛度，研究了軸承的熱特性、設計和應用參數對速度和動力學性能的影響，並進行了試驗驗證。 -
The friction coefficient, critical vertical loads and critical frictional resistance strength have been worked out by means of the pullout tests under the different vertical loads, analysis of frictional characteristics between soil and material and analysis of the different work mechanism between direct shear test and pullout tests. the creep characteristic parameters of some typical reinforcement materials have been obtained by the creep tests under the loads for a long time and the rheological analysis
對幾種典型筋材在不同法向荷載下進行了拉拔試驗，並進行了筋材與土介質的界面摩擦特性分析，直剪試驗與拉拔試驗不同機理分析，找出了影響摩擦特性試驗結果的主要因素；得出了筋材在工作荷載階段的摩擦系數、臨界法向中南大學博士學位論文荷載和臨界摩阻強度。 -
Loads analysis on finger of the machine for collecting plastic film residue
殘膜回收機撿膜桿齒的載荷分析
分享友人