locking position 中文意思是什麼
locking position
解釋
閉鎖狀態-
Intermittent transmission decollators are a new kind of hi - speed precise decollating organization, which can perform intermittent decollations, with characteristics like hi - precise decollation, smooth operation, wide transmission torque, position auto - locking, compact laid - out, small in size, low noise, and good durability
高速精密分割機構是實現間歇分度運轉新型機構，具有分度精度高、運轉平穩、傳遞扭距大、定們時自鎖、結構緊湊、體積小、噪音低、壽命長等優點。 -
The two locking bolts should be tightened first in order to position the flanges correctly as shown in fig. 1
為了如圖1所示正確定位法蘭，應該首先緊固兩個鎖定螺栓。 -
Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。 -
Stabilize your own position by locking up your savings
鎖住積蓄以穩固自己的位置。 -
The system is based on chopper constant current drive technique, according to the top level design idea, adopting advanced specical subdivision control integrate circuit and powerful function 80c196kc to organize the system frame, desiging the minimum system of single - chip microcomputer, multifunction i / o interface circuit, relay switch circuit, keyboard and display circuit, multifunction digital setting interface circuit and so on, utilizing the hso and hsi interface circuit which are owned by this single - chip microcomputer exclusively and its powerful command system to realize dual - degree switch control, automation orientation, automatically searching zero position, locking machine when stopping, frequency to set digitally, automatically adjusting speed through changing frequency, swithing subdivision or squarewave control, on the basis of above, the system also have the function of running according to the setting steps and the frequency, voltage and current to display through the led, etc
系統基於斬波恆流驅動技術，按照頂層設計思想，採用先進的專用細分控制電路和功能強大的80c196kc單片機來組建系統構架，設計了單片機最小系統、多功能i o介面電路、繼電器切換電路、鍵盤顯示電路和多功能數字設定介面電路等，利用該單片機獨有的hso和hsi介面及其強大的指令系統，實現了雙余度混合式步進電動機的余度切換控制、自動定位、零位自動搜索、停機鎖定、數字化頻率設定、自動調頻變速控制、細分方波切換控制，在此基礎上，該系統還設有按預置步運行、 led頻率電壓相電流顯示等功能。 -
Position the two halves of the flange adapter onto the groove in the valve body end ( s ), making sure that the tab on each flange adapter half is located between the two locking lugs on the valve body ( fig. 3a )
將法蘭適配器的兩半放置在閥體連接埠的溝槽上，確保每個半邊法蘭適配器上的孔位於閥體上兩個閉鎖凸榫上（圖3a ） 。 -
When actuation device stops at any position, a locking function is applied to avoid the displacement of actuation device due to external load
其可使執行機構在任意位置停止后，加以可靠的鎖定作用，從而避免執行機構在外界載荷作用下可能發生的位移。 -
Replace the arm on the turntable and tighten the height locking screw sufficiently to hold the arm in position
將唱臂重新裝上，將高度螺絲鎖到可讓唱臂固定。 -
Theoretically, we can calculate the transfer matrix between cube frame and robot - tool frame, because the relative position between marker cube and guiding robot is fixed. but error of mechanical interface is too serious to accomplish locking hole. we solve this problem by using neural net
針對導航機器人的標定盒與機器人之間存在加工和安裝尺寸誤差，導致標定盒坐標系與機器人工具坐標系之間坐標轉換不準確的問題，採用神經網路方法建立坐標轉換模型，從而規避了標定盒與機器人介面的機械誤差問題，實現兩坐標系之間的轉換。 -
Because the micro - tensioning system can hold the deflection in place, there is no need for repeated locking and unlocking of the cure position
因為微調系統能將彎曲的位置固定，所以不必反復鎖定和解鎖定彎曲的位置。
分享友人