loop control structure 中文意思是什麼
loop control structure
解釋
循環控制結構-
Depend on the comprehensive analysis and study of the structure, principle, and exterior characteristic of the motor, through the methods of system modeling and digital simulation analysis, two kind of control device that work for the low voltage ( lvdc ) and the high voltage ( hvdc ) in avigation are researched respectively. point to the control technique of close - loop speed stabilization at a limited adjustment speed range, we bring out the close - loop speed control method that using the rotor position sensor indirectly measure the speed of the motor
在全面分析了稀土永磁無刷直流電動機的結構特點、工作原理、運行方式以及外部特性的基礎上，通過系統建模和數字模擬分析，分別針對航空低壓直流（ lvdc ）和高壓直流（ hvdc ）兩種電動機構用永磁無刷電動機，在小范圍轉速連續調節下的閉環穩速控制技術進行了詳細理論研究，提出了利用轉子位置傳感器信號間接測量電機轉速進行電機轉速閉環穩速控制的策略。 -
After analysing several kinds of light - weighting structures through ansys, hexagonal speculum structure is confirmed. in the aspect of the controling of speculum, the paper adopts the brushless dc motor which is partial assembled to drive the point speculum and the inductosyn as angle measuring component is selected, the ad2s80a the system is used to get directly angle and angular velocity. double closed - loop speed and position control is designed, as the pid control is the well - developed algorithm, which can achieve stable rotation and precise position control
在指向反射鏡的擺動控制方面，採用低速性能好的分裝式直流力矩電機作為指向反射鏡的驅動電機，並採用感應同步器作為角度測量元件，運用軸角轉換器ad2s80a進行角度和速度的輸出，採用技術成熟的pid控制方案，進行速度和位置雙閉環控制，以實現指向反射鏡轉動速度的平穩性和位置的精確性。 -
Now with the development of computer control technique applied in it, computer control technique has had a profound influence on pneumatic system structure / control performance / control theory etc. this thesis deeply researches on the task - computer control smart high - speed pneumatic cushioning system. which mainly includes the design of mechanical structure / electronical circuit / pneumatic loop and the researches of system modeling / simulation / control strategy
計算機控制技術和電-氣比例伺服控制技術的結合，更是對控制系統的性能、系統的結構以及控制理論等多方面都產生了極為深刻的影響。本文對計算機控制智能高速氣動緩沖系統進行了機械、電氣、氣路系統的設計以及系統建模方法、系統辨識研究和控制策略研究。 -
On basis of the development of modern control technology and apply of the network technology and locale bus - mastering technology ， this text analyzes the essential element for produce of wire - roll mill : principle of assign for speed ; expatiates in detail on the network structure and communication protocol of ethernet and profibus - dp ; concretely describes the forms of control system configuration ， the function and features of its software and hardware designs ; also, introduces mainly control function of control system, ， for example ， sequence control 、 loop control 、 fly shear control and operation and monitor function etc
基於現代控制技術的發展、網路技術以及現場總線技術的應用，本文分析了線材生產的基本要素：速度的分配原則；分析了工業以太網ethernet和現場總線profibus - dp的結構和通訊協議。主要說明plc控制系統的組織結構形式，系統的軟硬體設計的功能和特點。同時，詳細介紹了控制系統的主要控制功能，如邏輯控制、活套控制、飛剪控制以及操作監控功能等等。 -
Pitch control system consist of three channels which is formed by three drive units. base on need of bench, drive system scheme is designed. single channel three - loop position servo system which is formed by linear motor is simulated. then kinetic behavior of rotor and system ’ s force coupling relation is analyzed. a compensation method for dynamic load which is caused by rotor rotation is presented base on structure - invarient theory
根據實驗臺的技術要求，設計了整個驅動系統方案。對由直線電機構成的單通道三環位置伺服系統進行了設計和模擬。分析了旋翼運動的動力學特性、系統力耦合關系，並根據結構不變性原理對由旋翼運動產生的動態載荷提出了補償方法。 -
The other way, theoretical analysis of weld tracking system with a leading sensor is stated, based on the analyzing of movement process of the tracking system, a loop control structure diagram is presented, the deuce vision feedback system is used and realized the repeated and automatic tracking in multiplayer seam and controlling of system of tracking and system of motion
同時就傳感器超前檢測式焊縫自動跟蹤系統進行了深入的理論分析，在分析該系統跟蹤過程運動關系的基礎上，建立了系統的閉環控制關系圖，並提出了其系統數學離散控制結構簡化圖。採用兩點式視覺伺服反饋系統，實現機器人在多層多道焊接時的重復自動跟蹤以及跟蹤機構的控制和焊炬橫向調節機構的控制，並使之協調聯動，滿足焊接過程的要求。 -
Closed - loop variable structure control method for seismically excited building structures
建築結構抗震控制的閉環趨近律方法 -
Based on the modularized asi, cascade inverter topology structure and modulation mode is introduced in this paper. comparing with several control strategies such as single closed - loop feedback and dual close - loop instantaneous value feedback, the voltage - current dual closed - loop control strategy, which is the voltage effective value feedback and inductance current instantaneous value feedback, is adopted
針對級聯逆變器討論其pwm調制技術，在比較幾種pwm調制技術的基礎上，對該級聯逆變器採用倍頻載波移相調制技術，其輸出不含載波諧波，邊頻諧波次數比二階和三階調制的邊頻諧波次數提高一倍，等效開關頻率也提高一倍。 -
In this system, according to the performance requires of servo - system in rapid character, high precision, drive - stiffness and high - speed stability, we adopted a closed - loop control structure that includes three closed - loops : position closed - loop, speed closed - loop and current closed - loop
根據伺服系統對快速性、高精度以及傳動的剛性和高的速度穩定性等方面的性能要求，系統採用了位置、速度、電流三閉環的控制結構。 -
The organization system is established according to the construction courses of hong - shui river long span bridge, which includes the loop of structure analysis, construction, test, forecasting, identifying, adjusting, preliminary announcement and construction. and the construction control flow process is established in this dissertation, as well as the solving programme
文中還根據紅水河特大橋的施工過程，按結構分析、施工、檢測、預測、識別、調整、預告、施工的循環特點，建立了組織機構，制定了施工控制流程和解決方案，實現大橋線形和應力的檢測和控制，效果良好。 -
This control structure allows for separate controllers to be designed to handle setpoint changes and load disturbances. another desirable feature is that it allows for simple closed - loop determination of the process model
這種控制結構允許對處理設定值改變和負載擾動分別進行設計，另一個特點是這種控制器考慮了過程模型的單閉環性質。 -
The stochastic structure and stochastic intelligent truss structure are taken as research object in this paper. the analytical model and method of the structural dynamic characteristic are investigated. when the applied forces are random excitation or random process ( stationary random process or non - stationary random process ) excitation, the structural dynamic response, the active vibration control for the intelligent structure, the optimal placement of the sensor and the actuator and the optimization of the feedback gains of the closed loop control system for the intelligent structure, and the effects of the structural parameters on the active vibration control et al are all studied systemically
本文以隨機結構和隨機智能桁架結構為對象，對結構動力特性分析模型與求解方法進行了研究；對結構在隨機力或隨機過程（平穩隨機過程或非平穩隨機過程）激勵下，結構的動力響應、結構的振動主動控制、智能結構中作動和傳感元件配置位置與閉環控制系統增益優化、結構參數對振動主動控制效果的影響等問題開展了全面而系統的研究。 -
Based on the characteristics of the giant magnetostrictive material, this article designs giant magnetostrictive micro - displacement actuator, and primary research contents are as follows : establishing drive magnetic field structure, designing closed loop control system, constant current source, temperature control system, magnetic field perceptual system and doing experiment testing
本文根據其工作特性設計了一種基於超磁致伸縮材料的微位移驅動器，主要研究內容包括:建立閉環控制系統、設計驅動磁場結構、恆流源驅動電路、溫控系統和磁場感知系統以及系統性能的實驗測試。 -
Considering the randomness of physics parameters of structural material, geometric dimensions, damping, loads and closed loop control voltage respectively or simultaneously, the analytic model of the stochastic structure under random forces are built. the solving methods are proposed. the computational expressions of the numerical characteristic of the structural dynamic response are developed
2 、考慮壓電智能桁架結構物理參數、幾何參數、結構阻尼和外荷載、閉環系統控制電壓分別或同時為隨機變量，構建了結構在隨機力作用下的動力響應分析模型，提出了求解方法，推導出結構動力響應隨機變量的數字特徵計算表達式，通過算例驗證了所建模型和所提求解方法的正確性和有效性。 -
In the course of open - loop control system, the simulation model of asynchomous motor is obtained and realized in simulink. this simulation model ' s structure is simple and its static and dynamic performance is good
在開環控制系統的模擬中，推導出一種異步電動機在mt坐標系下的模擬模型，該模型具有結構簡單、靜態、動態性能良好的特點，同時這個模擬模型也用於閉環系統。 -
Recursion is used as a primary control structure. in some languages, no other " loop " construct exists. there is a focus on list processing for example, the name
在程序中的兩處求得兩個不同的值，即使該表達式自身並沒有在其參數中使用任何可變變量。 -
This paper analyses the type, function and characteristics of usual proportional control valves and raises a new modificative version in the light of their drawback. that is, basing on the principle of flow amplification and electrical feedback and throughout calculation and analysis on flow closed loop control and pressure flow combination., determination of the minimum controlled pressure difference as well as flow controlling range and structure of main valve and research of the dynamic and static characteristic, the paper puts forward control principle of " flow - load pressure change - displacement revision " and pressure / flow double closed loop, and further expounds that using a proportional controller and a electric mechanical transducer can separately serve the control function of pressure or flow as well as flow pressure combination
本論文分析了目前常用比例閥的類型、功能、特性，並針對其不足提出新的改進方案，即：以流量放大，電反饋兩個原理為基礎，通過對流量閉環控制及壓力流量復合的計算分析、確定上最小控制壓差及流量控制范圍，確定主閥結構、功能特性研究等，提出了「流量? ?負載壓力變化? ?位移修正」的控制原理和壓力流量雙閉環控制原理，並進一步論述了利用一個比例控制器和一個「電?機械轉換器」就可完成獨立的壓力或流量控制功能以及流量壓力復合控制功能。 -
According to the structure characteristics and motion rules of the new type nursing robot, the close loop control system of this new type nursing robot is designed and made with the virtual instrument developing software labwindows / cvi, mcu, piezoelectric ultrasonic motor and high precision optical incremental encoder, which can make the robot reset and rotate by the predefined tracks. at the same time, in order to make the nursing robots used more widely where intensity, precision and price are not high, another control system is designed with the step motor, virtual instrument developing software labwindows / cvi, multi - function daq card pci1711, linear power amplifier. in order to use the nursing robots in acupuncture therapy, a simple finger is designed
在對其結構特點和運動規律分析的基礎上，本文以虛擬儀器編程語言labwindows / cvi為軟體開發工具，以單片機為控制核心，以超聲電機為驅動元件，以高精度光電編碼器作為速度和角位移檢測裝置，實現了機械臂的復位以及預定軌跡的閉環控制系統的開發;同時為適應一些強度不大、精度要求不高的應用場合，也為降低成本，簡化控制裝置，推動新型護理機械臂短期內應用推廣的需要，以目前應用較為廣泛、控制技術較為成熟的步進電機為驅動元件，用labwindows / cvi開發環境、 pci1711數據採集卡以及線性功率放大器開發了一套控制系統，實現了手臂的復位、勻速運動以及預定軌跡的控制系統;為推廣護理機器人在針灸理療中應用，設計了簡單的手指機構並利用labwindows / cvi開發環境，以及智能材料驅動器? ?層疊式壓電驅動器，進行了手指的抓取以及對驅動對象的轉動控制。 -
Second, based on the characteristic of handling - stability performance and the santana structure. the parameter 3d model of vehicle is success created, which includes suspension, steering, tire etc. according to the mechanism of adams closed - loop control, the closed - loop experiments are designed. dynamic simulation is realized and the simulate data is used to realize virtual experiment
其次，根據車輛的操縱穩定性能以及桑塔納轎車結構的特點，利用adams成功建立了包含懸架系統、轉向系統以及輪胎等結構的參數化三維實體結構整車模型，根據adams的閉環模擬控制原理，對整車模型進行了閉環模擬分析以及可視化處理，為虛擬試驗提供模擬數據。 -
Loop control structure
循環控制結構
分享友人