main amplifier circuit 中文意思是什麼
main amplifier circuit
解釋
主放大器電路-
The system cybernation method is distributed control system. in this way, the audio process computer switch the signal between input and output channels. the main function of audio process computer is general broadcast, service broadcast and emergency broadcast. there is a special control computer. it " s main function is supervise - control the system status such as the amplifier and speaker circuit
在控制上，採用了分散式控制方式，由語音計算機進行音源輸入和輸出的切換，執行業務性廣播、服務性廣播和火災事故緊急廣播；由控制計算機進行系統的監控，監視功率放大器和揚聲器迴路的工作狀態，並根據當前的設備狀態執行相應的控制任務。 -
In this thesis, one cycle controlled switching power amplifier is analyzed detailed in theory and researched in simulation and experiment. main work and conclusion are described below. first, the basic structure and operational principle of one cycle controlled half - bridge and bridge circuit are analyzed, and control equation are deduced
主要工作和結論如下：首先，對單周控制的半橋和全橋開關功率放大器的基本結構和工作原理進行了分析，推導了具體的控制方程，建立了單周控制的全橋開關功率放大器的小信號模型。 -
In the switched capacitor filter circuit, the properties of the operational amplifier influences the whole circuit severely, so this thesis introduce a typical operational amplifier that has two orders and tests the main properties of it
開關電容濾波器中，運算放大器的性能對整個濾波器的性能有著較大的影響，因此本文介紹了一種典型的兩級運算放大器的設計方法，並對該運算放大器的性能進行了測試。 -
In the charge pump principle section, the principle of linear mode and skip mode are analyzed in detail. the principle of step - up / step - down and the main parameters are also given in there. in sub - block circuit section, the typical circuits including reference, operational amplifier, thermal protection and current limit are introduced
在電荷泵基本理論中，詳細分析了線性（ linear ）模式、跳周期（ skipcycles ）模式和具有遲滯控制的跳周期模式;同時也介紹了電荷泵的升壓/降壓工作原理以及主要性能參數及其意義。 -
The main design work as follow : four biomedical analog signals input channels " design ; the design of at89c51 microprocessor system which can change the sampling rate ; the dma interfacing circuit design by which the sampling data enter the computer ; the interfacing circuit design between pc and signal amplifier, and the reliability and anti - interference design of this system, etc
具體設計內容包括：四路生物醫學模擬信號輸入通道設計；以at89c51為核心的可實現采樣速率程式控制調整的微處理器系統設計；采樣數據進入pc機的dma介面電路設計； pc機與生物信號放大器之間聯系的介面電路設計；以及系統的可靠性和抗干擾設計等。 -
In order to make full behavior simulation of sigma - delta modulator, the noise models have been set, taking into account most of the sigma - delta modulator ’ s non - idealities and the final result supports the noise models. last, the main circuits of modulator have been designed, such as operational amplifier, comparator and clock generator, the design principle of noise - killed logic circuit has been presented. these circuits have been simulated
調制器的噪聲模型，考慮了影響調制器性能的一些主要非理想因素，通過模擬驗證了噪聲模型的正確性;最後，設計實現了結構中的主要電路，如運放、比較器、時鐘產生電路，闡述了噪聲抵消邏輯電路的工作原理，利用hspice和cadencespectre對各電路進行了模擬，驗證其功能。 -
In the analog ic, one of the typical circuits is operational amplifier. therefore, the design of low - voltage and low - voltage operational amplifier is very necessary. while realizing low - voltage and low - power, it must be noticed for the implementing of the main function of the circuit. because the low supply voltage affects performances of circuits, it is not very good for just implementing low - voltage and low power but not implementing the good performances
在模擬集成電路中，運算放大器是最典型的電路之一，所以設計低電壓低功耗的運算放大器是非常必要的。在實現低電壓低功耗的過程中，必須考慮電路的主要性能的實現，因為電源電壓的降低將影響電路的性能，只是實現低壓低功耗而不實現良好的性能是不大妥當的。 -
To reduce power dissipation of the amplifier, a kind of on / off technology is used in the circuit. with a little bias current circuit to control the main bipolar transistor operation, the transistor will be in a state of on / off
採用器件旁路小電流工作電路，實現對低噪聲放大器主要工作晶體管的控制，使該晶體管按需要分別處于工作或關斷狀態，保證了放大器的極低功耗。
分享友人