measuring engine 中文意思是什麼

measuring engine 解釋
測量機
  • measuring : n. ,adj. 測量（的），測量用（的）。 remote measuring 遙測。
  • engine : n. 1. 機械，機器。2. 引擎，蒸汽機，發動機。3. 機車，車頭。4. 工具；〈古語〉方法，手段。vt. 給…安裝發動機。
  1. This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves

    2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。
  2. There are the production lines established of intermediate - frequency melting, silicasol shuck, precision casting and metal ceramic, and 250 universal devices suck asvacuum melting electric furnaces, high - temperature and intermediate - temperature heat treatment electric furnaces, digitai - control lathes, milling and drilling machines, coreless millers, spherical surface millers, standing milling machines and so on, lt has established the central measuring roomm physicallab, chemical lab, metallic phase lab, crack detection test lab, seat ring lab, rocker lab and ducgt trestle lab, our esported gas engine valve seat to america was rewarded the second prize in terms of sichuan high - quality product

    建有中頻熔煉真空熔煉硅膠溶模精密鑄造粉末冶金生產線。有中頻電爐真空熔練電爐高中溫熱處理電爐數控車床鉆銑床無芯磨外園磨立磨等通用設備250臺套。有中心計量室物理化學金相探傷檢測及座圈搖臂導管臺架實驗室。
  3. Some testing devices are of advanced ones, such as scanning electronic microscope, microfocus circular radioscope, water - immersed ultrasonic flaw detector, 3 - axis measuring machines, large - sized projector, etc. for the production of non - aero products, there are large - sized die - casting equipment, and nearly 100 pieces of specialized gear machine tools including worm - gear grinding machine, etc. it has some specialized production lines for piston, crankshaft, cylinder and housing, etc., as well as 4 flexible production lines advanced at home for motorcycle engine, and a complete set of automatic inspection test eqiuipment for motorcycle engine

    計算機輔助設計輔助加工技術正在普遍使用。在非航空產品生產方面有大型壓鑄設備殼型鑄造，包括鍋桿輪磨在內的輪專用機床100多臺，以及活塞曲軸汽缸殼體等專業化生產線。此外，還建成了具有國內領先水平的4條摩托車發動機柔性生產線，以及成套的摩托車發動機檢測設備，可進行測試數據分析，改進檢定測試方法等。
  4. During the process of measuring compression ratio, the viscous fluid instead of burning gas is applied to measure the maximal volume. residual volume and working volume of the engine combustion cylinder respectively

    在壓縮比測量裝置中，採用粘性液體，代替發動機工作燃氣，分別測量出發動機燃燒工作室的最大容積、余隙容積和工作容積，方便地計算出發動機的壓縮比。
  5. Presented in a newly developed measuring & control system used for internal combustion engine rig test

    摘要介紹了一種新開發的適用於發動機鑒定試驗的自動測量控制系統。
  6. Abstract : presented is a newly developed measuring & amp, control system used for internal combustion engine rig test

    文摘:介紹了一種新開發的適用於發動機鑒定試驗的自動測量控制系統。
  7. Measuring technology for internal - combustion engine

    內燃機檢測技術
  8. The measuring method of vibration for small gasoline engine

    小型汽油機振動測試方法
  9. Measuring engine transient process data in ca1258p1k2l11t1 truck in accelerated mode, recording and analyzing the data, then analysis the test error. 4. building model and simulating two typical running mode ? fixed 6th gear acceleration with initial vehicle speed 40km / h and gear change acceleration starting with 2nd gear, comparing calculated result with test result, revising transient process simulation model and analyzing error between calculation

    本文基於ca1258p1k2l11t1載重卡車對ca6df2 - 26發動機的瞬變工況進行試驗和模擬計算，結果表明: 1 ） gt - power軟體可以很好的模擬、分析、預測發動機瞬變過程，模擬計算的結果與試驗結果很接近，試驗證明，預測分析指出的改進方向是正確的; 2 ）加裝電動增壓器可以降低整車使用油耗，改善低速煙度排放，縮短加速時間，改善整車的加速響應; 3 ） gt - power軟體預測分析配合發動機和整車試驗是分析、解決發動機瞬變過程的有力工具。
  10. The instantaneous torque measurement system has been improved, which uses slip ring to transmit signal, improved measuring accuracy and stability, the mechanism of occurring of instantaneous maximum torque has been understood during changeover of the main engine

    改進了集流環傳輸信號的瞬時扭矩測量系統，提高了測量精度和穩定性，進一步認清了在主機切換過程中瞬時扭矩的極大值產生的機理。
  11. Gamma - ray observations help astronomers understand the basic physics of these sources by measuring the energy and variability of the highest energy radiation coming from these sources, radiation often comes directly from the central engine

    通過對這些輻射源的高能輻射變化及能量的測量，射線的觀察有助於天文學家了解這些通常直接來自能量中心的輻射源的基本物理性質。
  12. Study of infrared measuring temperature of exhaust manifolds of locomotive diesel engine

    機車柴油機排氣支管紅外測溫方法的研究
  13. Road vehicles. garage equipment. engine testing and measuring equipment

    道路車輛.汽車車庫工具.測量和檢驗工具
  14. 3. design and develop the device of motorcycle engine valve phase measuring system

    3 、摩托車發動機氣門相位測量裝置的設計開發。
  15. 2. analyze and compute the theory of motorcycle engine valve phase and compression ratio measuring system

    2 、對氣門相位、壓縮比測量的理論分析和方法計算。
  16. Main contents are listed as follows : 1. survey the present status of motorcycle industry engine valve phase and compression ratio measuring technology in our country

    本文主要包括如下的內容： 1 、目前我國摩托車行業發動機氣門相位、壓縮比測量技術現狀的調研。
  17. This paper presents the establish process of motorcycle valve phase and compression ratio measuring system during the development of motorcycle engine for the jia ling industry group

    本文介紹了嘉陵工業集團摩托車發動機開發中，氣門相位和壓縮比測量系統的建立過程。
  18. Methodological research of measuring motorcycle valve phase and compression ratio is put forward in this paper. the devices mentioned above can be applied to develop and manufacture such kind of motorcycle engine. farther research work can be carried out to discover more valuable results

    本文提出了一種測量氣門相位和壓縮比的方向性方法，文中所述的裝置可以完全運用於科研開發和生產實際中，同時可對該種方法開展進一步的研究。
  19. The product widely uses in the automobile, the motorcycle, the electrically bicycle and the part, the clearer, the gasoline engine, the sewing machine, the electrical machinery, the instrument measuring appliance, the domestic electric appliances, the computer, the color television, the air - conditioner, the electric refrigerator, the washer, the cooking utensils, conserves energy electronic profession each kind of assembly production lines and so on the lamp, cosmetics, correspondence, transportation, water pump, food plastic product

    產品廣泛用於汽車、摩托車、電動自行車及配件、清洗機、汽油機、縫?機、電機、儀器儀表、家用電器、電腦、彩電、空調器、電冰箱、洗衣機、炊具、節能機、化妝品、通信、交通、水泵、食品塑料製品等電子行業各種裝配生產線。
  20. According to the relational expression of torsional vibration of the measuring point on crankshaft and the excited moment of each cylinder of internal combustion engine ( ice ), the working condition of each cylinder was monitored and the fault of cylinder - scoring was diagnosed using the amplitude and phase characteristic of 0. 5 order torsional vibration

    摘要依據內燃機軸系測點扭振與各缸激振力矩的關系式，利用0 . 5諧次扭振的幅值與相位特性，進行內燃機各缸作功狀態監測和拉缸故障診斷。
分享友人
分享到 Line

分享到臉書