mill load 中文意思是什麼

mill load 解釋
軋機負荷
  • mill : n 1 米爾〈姓氏〉。2 James Mill 詹姆斯米爾〈1773 1836，英國經濟學家〉。3 John Stuart Mill 約翰斯圖...
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  1. Based on practical project of inspecting, appraising and reinforcing a main heavy factory building, especially its steel crane girder system, of the second steel mill belonging to taiyuan steel & iron corporation, whose technology renovation leads to increase tonnage of many heavy cranes and vertical load of frame - bent structure, first the structure and its members were investigated, inspected, calculated and analyzed, and their reliability was appraised respectively and the strengthening projects or the measures to remedy were given. then, in accordance with the requirement to strengthen the girders under non - stop production, the feasibility of strengthening the crane girders by adding steel diagonal braces underneath the existing girders has been studied by inspecting and evaluating the strengthening effect of the crane girders and comparing with other reinforcing scheme

    本文結合太鋼（集團）有限公司第二煉鋼廠主廠房由於生產工藝改造要求，加大多臺重型吊車噸位及bc跨（ 1 ） （ 8 ）軸線框排架各層豎向（設備）荷載后，對廠房結構，尤其鋼吊車梁系統進行檢測鑒定與加固設計的實際工程，首先對廠房結構進行了現場調研、技術檢查、測試以及內力和承載能力的計算與分析（考慮抗震） ，並根據檢測、計算與分析結果，對廠房結構、構件的可靠性進行了評定，並綜合提出鑒定結論和加固處理建議。
  2. The load monitoring and optimal dispatching for paper mill

    造紙廠負荷監測和優化調度系統
  3. Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape

    摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。
  4. The overhead traveling crane used at a cold strip mill factory is given to study the deformation, stress distribution and load capacity of the main girder with 3d - fea shell - to - solid submodel method

    以某冷軋帶鋼廠橋式起重機偏軌箱形梁為例，採用三維有限元法「板到體子模型」技術，比較分析了加強板2種焊接方式下主梁的變形、應力分佈和承載能力。
  5. A rolling load distribution optimization algorithm of tandem cold mill was designed using particle swarm optimization algorithm

    摘要利用粒子群演算法設計了一種冷連軋軋制負荷分配的優化方法。
  6. Tests demonstrate that the using particle swarm optimization algorithm to optimize load distribution has the advantages of simpleness, fast speed and high degree of convergence, which can be generalized as a new method of rolling load distribution of tandem cold mill

    實驗證明，粒子群演算法在軋制負荷分配計算中，具有演算法實現簡便、運算速度快、收斂性好等優點，可以作為一種冷連軋軋制負荷分配的新方法加以推廣。
  7. Excess additive can create over reduction allowing more load on the mill and reducing speed

    過量投加會造成過度變形量進而對軋機形成更多的負荷並降低速度。
  8. The ball mill load - control apparatus adopted the assembly language and the c51 language to program and its concerned software was designed, including the data collection, the wave - percolation, the short - time average over - zero ratio, the estimation of the power chart and the average - period chart

    磨機負荷控制儀軟體使用匯編和c51編程，本文進行了相關軟體的設計，包括數據採集、濾波、短時平均過零率、功率譜估計和平均周期圖等。
  9. Research of load measuring device of oil film bearing used in high - speed wire rolling mill

    高線軋機油膜軸承載荷特性測試裝置研究
  10. Study on new technique of automatic testing of grinding mill load

    磨機載荷新型自動檢測技術研究
  11. Present state and development trend for ball mill load measurement

    球磨機負荷檢測的現狀與發展趨勢
  12. According to the results of the analysis and the experiment, the mathematic model of the ball mill load - control apparatus was established and its sample was successfully designed

    根據多次試驗和分析結果，建立了球磨機負荷控制系統的數學模型，也完成了其樣機的設計。
  13. Compares with the same centripetal ball bearing, has the big radial direction load bearing capacity, mainly is suitable for the cold hot - rolling mill, working roll support rolls and so on cogging mill

    與相同的向心球軸承相比，有較大的徑向負荷承載能力，主要適用於冷熱軋機，開坯機等工作輥支承輥。
  14. Taking the soft ? sensing of oxygen content in flue gas, unburned carbon content in fly ash and coal load in ball mill as examples, we emphatically analyze the current status, modeling method of their soft ? sensing and the secondary variable selection in the soft ? sensing ; and also summarize some other thermal parameter soft ? sensing techniques in our country, which is a guidance for the development of the thermal parameter soft ? sensing technique in power plant, and has some value for the optimization of thermal control systems

    以煙氣含氧量、飛灰含炭量、球磨機負荷為例，著重分析和總結了其測量的現狀、軟測量建模方法和二次變量的選取，並概括了國內現有的其他熱工參數軟測量技術，對火電廠熱工參數軟測量技術的發展具有一定的指導意義，對熱工控制系統的優化具有一定的參考價值。
  15. Load of gear box can be decided by measuring of low speed shaft contort. in mill system of single - pinion drives

    邊緣傳動磨機系統，可以通過實測低速軸的扭矩來確定系統中減速機的負載狀況。
分享友人
分享到 Line

分享到臉書