mirror assembly 中文意思是什麼
mirror assembly
解釋
反射鏡裝置-
The research result indicated : for the strip primary mirror discussed in this article, the hexagon light - weighted cell has the best structural rigidity quality, the square cell is a little worse, the triangle cell is the worst ; there is an optimum on primary mirror thickness ; on condition of 1g gravity load combining with 4 centigrade uniform temperature rising, the thinner and higher of the flexible support reed, the better of the primary mirror surface figure. the decision of the structural parameters of the flexible support reed must take static rigidity, dynamic rigidity, static strength and dynamic strength of primary mirror assembly into account
研究結果表明：對于本文的長圓形主鏡，採用正六邊形輕量化孔，鏡體結構剛性品質最好，正方形次之，正三角形最差；主鏡鏡體厚度存在最佳值；主鏡組件在1g重力、均勻溫升4共同作用的工況下，主鏡柔性支撐簧片厚度越小、高度越高，主鏡綜合面形誤差（ p - v值）越小，但同時主鏡組件的剛體位移增大、固有頻率下降，因此柔性支承結構參數的確定要綜合考慮主鏡的綜合面形誤差和主鏡組件靜態剛度、動態剛度、靜態強度和動態強度等因素。 -
It is also an important consideration in the structural design of the primary mirror assembly whether the primary mirror assembly can withstand the effect of dynamic load from the ground transport and the space launch process
計算表明，在發射過載條件下，主鏡組件不會失穩。主鏡組件能否經受住地面運輸和空間發射階段動力環境的考驗，是主鏡組件設計校核的一個重要方面。 -
The dynamic analysis indicates that the design of the primary mirror assembly is good. the design of the primary mirror assembly meets requirements
主鏡組件有限元模型動力學分析表明，本文設計的主鏡組件足以抵抗動力學環境載荷的影響。 -
That is, by the calculation of the anti - thermal deformation quality factor and synthetic quality factor of some typical primary mirror materials, the primary mirror material is selected scientifically and rationally. by the finite element method and the conception of structure rigidity quality factor, researching the relation between the light - weighted cell shape, the mirror thickness and mirror structural rigidity quality. by the force - thermal coupling analysis of the primary mirror assembly, the relations between the thickness, height of the flexible support reed and primary mirror synthesis surface figure error ( p - v ) have been researched
即，通過對常用主鏡材料的抗熱變形品質因數和綜合品質因數的定量分析，科學地完成了主鏡的選材；應用有限元分析方法，藉助于結構剛性品質因數的概念，研究了主鏡輕量化孔的形狀和主鏡厚度對鏡結構剛性品質的影響；通過對主鏡組件的力熱耦合分析，研究了主鏡柔性支撐簧片厚度與高度對主鏡面形的影響。 -
For the flexible support reed is very thin ( 1. 3mm ), it ' s necessary to study the buckle of the primary mirror assembly. the calculation indicates that when space camera is launched, the primary mirror assembly would work well
為了滿足主鏡的設計約束條件，主鏡柔性支撐簧片厚度設計的較薄（ 1 . 3mm ） ，因此有必要對主鏡組件的結構穩定性進行校核。 -
Please note that images formed by this mirror assembly are laterally inverted
請注意這個鏡子組合的影像左右倒轉了。 -
It might preferable, however, to use shperical mirror for the first step studies of euvl in a series investigation of system design, component fabrication, assembly technique and experimental process. along this thought, the author designed a schwarzschild optics using spherical mirrors with 10 : 1 reduction projection optics
作為研究的第一步，出於進行euvl原理及系統設計、光學元件的制備、系統集成、掩模曝光實驗等相關技術研究目的，採用球面schwarzschild微縮投影物鏡是比較切實可行的技術方案。
分享友人