modulator amplifier 中文意思是什麼
modulator amplifier
解釋
調制器放大器-
In the thesis, a high efficiency linear am amplifier is developed, which is based on the basic theory of eer linearization amplifier technique [ 1 ]. the high efficiency digital audio amplifier technology [ 2 ] is adopted to develop the power supply modulator and the class - d switching amplifier technology [ 3 ] is adopted to develop the high efficiency rf amplifier
本論文利用eer （ envelopeeliminationandrestoration ）線性功放技術的基本原理[ 1 ] ，採用數字音頻功放技術[ 2 ]實現高效率電源調制器，採用class - d開關放大技術[ 3 ]實現高效率載頻放大器，開發了一個集am調制和放大於一體的高效率線性功率放大器。 -
Because of the using of interpolation, noise shaping and switching amplification in the digital audio amplifier technology, the power supply modulator is not only much efficient but also behaving good in envelope amplification, this advantage is hard to implemented with conventional technology
數字音頻功放技術是近年發展起來的高效率音頻放大技術，該放大技術採用了過取樣、噪聲整形等數字音頻處理演算法和開關功率放大。採用該技術實現的電源調制器不但具備很高的效率，而且能高指標地放大包絡信號，是常規的電源調制技術無法實現的。 -
And the ways to optimize the circuit architecture, minimize the circuit nonidealities and improve the circuit performance are analyzed combined with the characteristics of the modulator architecture. based on it, the switched - capacitor integrator, class a amplifier, nonoverlap clock, voltage reference, comparator, feedback dac have been designed. in the end, the layout design is shown
調制器採用全差分開關電容電路實現，並根據系統結構特點就如何優化電路結構、克服電路中存在的非理想特性、提高電路性能作了具體分析，在此基礎上完成了開關電容積分器（開關、電容、運算放大器） 、參考電壓源、比較器、兩相非交疊時鐘、反饋dac等模塊的電路結構和參數設計。 -
The core of the lock - in amplifier used to measure response of laps consists of a high precision modulator / demodulator and dds as signal generator
對于光尋址電位傳感器，我們設計了以高精度數據機件和數字頻率合成器件為核心的模擬鎖相放大器。 -
The experiment results show that : the frequency stabilization of the optimized doppler modulator has already reached rms error about 1 %, which could meet the need of reference signal of the lock - in amplifier
實驗結果表明，經過優化后的多普勒調制器的輸出調制信號頻率的相對標準誤差達到了1 %左右，能夠滿足鎖相放大器對輸入參考信號頻率穩定度的要求。 -
Based the research on the laser beam drift feedback control technique, analysing the beam drift and its frequency components, a laser beam directional stability method is studied in the thesis in detail, with its measurement and control circuit system that combines the laser beam intensity modulation and the beam drift feedback control technique. in this method, at first the laser beam intensity is modulated with the acoustooptic modulator, then the lock - in amplifier is applied to detect and demodulate the modulating signal, at last a feedback control signal is generated by the dsp control circuit at last, including : 1
本文在原有的激光光束漂移量反饋控制準直技術的基礎上，對光束漂移量信號的數據和頻譜進行了分析，重點研究了一種集聲光調制光強與光束漂移量反饋控制準直技術於一體的激光光束方向穩定方法及其測控電路系統，該方法通過聲光調制實現光強調制，接著通過鎖相放大電路檢測並解調調制信號，然後通過dsp控制電路進一步對光束的漂移量進行反饋控制。 -
Five key devices are studied, which are millimeter wave low power amplifier, millimeter wave low noise figure amplifier, millimeter - wave 0 / phase modulator, 14 to 56ghz millimeter wave quadruples
重點研究了五種毫米波關鍵部件，包括毫米波小功率放大器、毫米波低噪聲放大器、毫米波0 /調制器、毫米波單刀雙擲開關、 14 56ghz毫米波四倍頻器。 -
In order to make full behavior simulation of sigma - delta modulator, the noise models have been set, taking into account most of the sigma - delta modulator ’ s non - idealities and the final result supports the noise models. last, the main circuits of modulator have been designed, such as operational amplifier, comparator and clock generator, the design principle of noise - killed logic circuit has been presented. these circuits have been simulated
調制器的噪聲模型，考慮了影響調制器性能的一些主要非理想因素，通過模擬驗證了噪聲模型的正確性;最後，設計實現了結構中的主要電路，如運放、比較器、時鐘產生電路，闡述了噪聲抵消邏輯電路的工作原理，利用hspice和cadencespectre對各電路進行了模擬，驗證其功能。
分享友人