mold cooling 中文意思是什麼
-
On most automotive battery grids, cooling is required in the top gate area and in the center of the mold only.
絕大部分汽車蓄電池板柵尺需要在頂部澆口部分和模具的中心冷卻就可以。 -
The wax setting and casting process is complicate process with a series of procedures, including model creating, spruing and construction, rubber mold vulcanization and cutting, wax models injection, stone setting in wax model, wax tree creating, investing, investment mold burning - out, metal melting and pouring, casting cooling and divesting, etc
蠟鑲鑄造是一個多工序的復雜工藝過程，包括母版製作、開設水線、製作橡膠模、製作蠟模、寶石鑲嵌到蠟模、種蠟樹、製作石膏型、石膏型脫蠟焙燒、金屬熔煉澆注、飾件冷卻清理等。 -
For alloy insert parts. that can increase cooling ability & parts releasing from the mold. increase 25 % productiity may be more. & that also help for to stabilize dimension
作合金鑲嵌件，以提高局部冷卻效果及易於脫模，提高生產率25 %以上，並可解決尺寸穩定性方面的問題。 -
For alloy insert parts. that can increase cooling ability & parts releasing from the mold. increase 25 % productivity may be more. & that also help for to stabilize dimension
作合金鑲嵌件，以提高局部冷卻效果及易於脫模，提高生產率25 %以上，並可解決尺寸穩定性方面的問題。 -
Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure
文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致 -
Mold temperature is controlled by water flow in cooling channels.
模具溫度可用冷卻槽中水的流動來控制。 -
Aozhan company concentrate on development of “ special oily agent ”, which have owned countless great accomplishment and gradually becomes taking characteristic “ anti - rust, lubrication, cleaning, cooling ” as “ silver brilliant ” series of special long - term and mid - term anti - rust agent, special mold release agent, cleaner and thimble oils and so on
奧展公司致力於「特種油劑」的開發已碩果累累，逐步形成以「防銹、潤滑、清洗、冷卻」為特色的「銀晶」牌特效模具長期、中期防銹劑、特效離型劑、清洗劑、頂針油等系列產品。 -
Furthermore, to avoid the craze of the target caused by the brittleness of si element, a new mold and cooling method have been developed. in the second part, the material of the resistor coatings has been studied
此外，為了防止靶材的破裂，降低其內應力，自行設計了熔煉模殼及冷卻方法，有效的解決了靶材的開裂問題，使靶材熔煉的成品率達到90 %以上。 -
Over the life of the mold, corrosion in the cooling channels decreases cooling efficiency thus degrading part quality and increasing cycle time
超過模具生命的，冷卻系統的腐蝕降低了冷卻的效率，因此會降低產品的質量並且增加成型時間。 -
So we suppose it as an infinite plane and build the model to simulate the cooling process of the gmt in the mold
以此為基礎，建立模型對gmt在模具內冷卻過程進行模擬。 -
Abstract : the article briefly describes the application and theoretical studies of solidifi - cation simulation for mold and secondary cooling zone of continuous casting
文摘:介紹了連鑄時結晶器及二冷區中凝固模擬的應用與理論研究工作。 -
The pipe extrusion machine set works through applying single - screw extruders to extrusion, vacuum mold to molding, cooling tank to cooling, hauling engine to drawing, and saw or planet cutter to cutting
本款管材擠出機組工作原理是：由單螺桿擠出機機頭擠出，型模真空定型，冷卻槽冷卻，牽引機引出，鋸切機或行星切割機最後進行切割。 -
This is accomplished by melting plastic resin ; injecting it into the mold and then having the part separate from the mold on cooling
這由把可塑的樹脂熔化來完成，將之注入模型然後當冷卻時從模型中將這個部分分離出來。
分享友人