molten alloy 中文意思是什麼
molten alloy
解釋
鑄造合金-
The sodium silicate makes the cork stick to the mold surface and also helps to withstand the charring action of the molten lead alloy.
硅酸鈉能使軟木粉粘結在模具表面，而且還有助於軟木粉耐受熔融鉛合金的碳化作用。 -
An alloy of ferromanganese is added to the molten metal as it is poured from the converter into the ladle.
人們在鋼水輕爐倒進鋼水桶時，放進一些錳鐵合金。 -
Numerical analysis of ternary alloy molten pool heated by electron gun
電子槍加熱三元合金熔池的數值分析 -
The main reasons causing increased chilling tendency of nodular iron are as follows : using metal charge containing trace and alloy elements which can increase chilling tendency ; molten iron being holded at high temperature too long ; abnormal nodularizing and / or inoculation treatment, as well as abnormal composition control
摘要引起球鐵白口傾向大的主要原因是：爐料穩定性差、電爐保溫、球化處理及鐵液成分控制和孕育處理出現異常。 -
Tin is important as it imparts an improved "fluidity" to the molten alloy and helps in mold filling.
加錫是很重要的，因為它可以改進熔融合金的流動性，從而使其易於注入模具。 -
The pressureless infiltration technique means that the spontaneous infiltration of the refined molten al or al - si alloy into the power bed, contains the filler reinforcement particle and k2tip4, occurred at 900 to fabricate sicp / al or sicp / al - si composites, without the aid of any externally applied pressure or vacuum, only by its gravity
無壓自浸滲法是指在不藉助任何外力作用下，把熔煉好的鋁液，經精煉，調溫后，澆入經過預熱，含有增強體顆粒與助滲劑的混合體粉末中。 -
Copper - nanosized tibi composites were prepared by in - situ process. the microstructure, mechanical and electrical properties, and dry sliding wear behavior and electric sliding wear of cu - nanosized tib _ 2 in - situ composites was investigated ; mostly task as follows : the thermodynamic data for the reactions between b and ti in the molten liquid of copper were analyzed, the copper matrix composites reinforced by in - situ tibi nanoparticles were prepared by reactions of 8263, carbon and titanium in copper - titanium melt, and copper - titanium, copper - boron in alloy melt, respectively, which controlled the reaction temperature, reaction time and solidification process. the rnicrostructure and mechanical and electrical properties of the in - situ composites were investigated by using optics microscope, tem and xrd
本文採用原位反應法制備了cu -納米tib _ 2原位復合材料，在此基礎上分析了原位復合材料的微結構，進行了干滑動摩擦磨損和電接觸滑動磨損實驗，完成的主要工作如下：從熱力學的角度出發，分析了陶瓷tib _ 2顆粒在銅基體中原位生成的熱力學條件，並用電解銅、工業純鈦、 b _ 2o _ 3 、 c （還原劑）以及cu - ti 、 cu - b等合金為原料，通過控制適當的反應溫度、反應時間和快速凝固等工藝手段，制備了cu -納米tib2原位復合材料。 -
This paper offers a comprehensive review of the current status of application of the high - temperature corrosion - resistant materials used widely by glass industry, as well as a description of the mechanism of metal and alloy corrosion in molten glass
摘要敘述了國內外玻璃工業常用高溫耐蝕材料的應用現狀，並就其中的金屬及合金材料在熔融玻璃中的腐蝕機理作了介紹。 -
In this thesis, as a new method of fabrication metal composites, directed reaction of molten metal ( casting process ) makes the particles - reinforced phase, the product of chemical reaction in the metal or alloy, be distributed homogenously in the matrix
本研究提出了一種制各al _ 2o _ 3 cu復合材料的新型方法? ?熔體直接反應法（熔鑄法） ，它是通過金屬液或合金液中發生化學反應生成增強相顆粒，並使之均勻分散於基體之中。 -
In order to decrease chilling tendency, it is suggested to shorten holding time of molten iron at high temperature ; adopt nodularizing alloy with low rear earth content ; reduce trace elements and bismuth contents of the metal charge
為減小球鐵的白口傾向，建議：縮短高溫停留時間；採用低稀土球化劑；加強爐料控制，減少微量元素，避免鉍量過高。 -
The results showed that the processing parameters ( such as laser power, the diameter of laser, scanning speed of laser beam, ratio of overlapping ) are important to acquire a perfect component. furthermore, in order to assure geometric properties ( accuracy, surface finish ), the structure of the off - axial powder nozzle was improved to avoid the oxidation of the molten pool. the density metal test sample of rene95 high - temperature alloy was made by lsf through optimizing the processing parameters
本文對激光立體成形的工藝特性進行了深入系統的研究，發現如果要獲得理想的成形效果，就必須對成形過程中的工藝參數進行精密控制，例如激光功率、激光光斑大小、光束掃描速度、搭接率等；同時為了保證成形件有較高的尺寸精度和表面質量，必須對成形零件的氧化問題進行控制，通過改進側向送粉噴嘴的結構設計，成形件的表面氧化問題得到適度控制。 -
In order to insure of the quality of yongtong alloy steel and make a brand name product of china, yongtong, working together with famous universities by means of optimizing the materials, and using clear molten iron for steelmaking
為充分保證"永通"牌合金鋼的品質，打造中國的特鋼名品，永通特鋼依託國內知名院校，從優化原料入手，用純凈的鐵水滿足煉鋼需要。 -
The phase composition, microstructure and the interface characteristic were all analyzed through xrd, sem, optical microscope, eds, etc. the results are listed as follows : the growth mechanism of al - 5zn - 10si alloy is that molten aluminum keep a continuous oxidation and growth in the way of cell - shape through the micro - channels which transfer the molten aluminum to the reaction front
採用xrd 、 sem和光學顯微鏡以及能譜分析法，研究分析了al _ 2o _ 3 sic ni al - si合金多相陶瓷基復合材料的相組成及其界面特徵。研究發現： al - 5zn - 10si合金原位氧化生長是合金熔體通過氧化體中的微觀通道傳輸到氧化生長體前沿繼續氧化，並以胞狀形式向前生長。 -
The widely used mg alloy zm5 is chose as the original alloy. on the surface of the molten alloy, a layer of protective film with dense structure is formed by the addition of la, ce or mischmetal. the film prevents the penetration of oxygen and volatilization of mg vapor, and then prevents the zm5 alloy from oxidation and burning
針對目前廣泛應用的zm5鎂合金，通過添加稀土鑭、鈰和混合稀土，在鎂合金液面上形成一層結構緻密並且具有耐久性的保護膜，阻止氧氣的進一步侵入和鎂蒸氣的向外揮發，不再產生鎂的劇烈氧化燃燒現象。 -
Evaluation criterions for modification effect of molten al - si alloy
合金熔體變質效果評估判據
分享友人