needle pressure 中文意思是什麼
needle pressure
解釋
針端壓力-
Specific means is preexistence reaction spot is located inside chosen acupuncture point area, the handle that use a needle ( or match rod ) press pressure, its have the place of tenderness to be reaction dot namely, radish is stuck with adhesive plaster after disinfection child ( turnip seed ), after affixing fat acid bilges feeling can, choose 3 every time 5 point, pressure after sticking fat or the parent, daily proper motion is pressed press 3 4 times, change every week, or so ear undertakes alternately, such holding to that treat 1 3 months, what can control children is fat
具體方法是先在選用的穴區內找出反應點，用針柄（或火柴棍）按壓，其有壓痛的部位即為反應點，消毒後用膠布粘萊菔子（蘿卜籽）一粒，貼上之後胖兒有酸脹感即可，每次選3 5個穴位，壓貼后胖兒或家長，每日自行按壓3 4次，每周換一次，左右耳交替進行，這樣堅持治療1 3個月，能夠控制兒童的肥胖。 -
Methods : a self - made sensing needle was used to measure calcium ion concentrations of dachangshu ( bl25 ), ganshu ( bli8 ) and guangyuanshu ( bl26 ) and their corresponding non - acupoints in 8 sheep ; oxygen partial pressure of ganshu ( bl18 ) and housanli ( ex ) and their corresponding non - acupoints were also observed
方法：利用自製的傳感針，在體監測8隻山羊的大腸俞、肝俞和關元俞及其對應的非穴位點的鈣離子濃度；並監測肝俞和后三里及其對應非穴位點的氧分壓。 -
The filtered solids are systematically removed from the filter during the back - flushing operation. back - flushing is actuated as a function of the differential pressure or a pre - set time, depending on the degree of contamination of the needle - slot candles
過濾機的清洗排污過程是在設備運行過程中自動進行的，反沖時逐一清洗每個濾芯，其它濾芯仍在連續過濾，可保證濾液的連續供給。 -
The contents of the thesis are as follows : ( 1 ) all the contents : magnetism sense fuel injector is designed. needle valve lift signal, rotation speed signal and pressure signal are collected and processed. circuit is designed. programme is programmed. ( 2 ) contents studied : the item is completed
本課題的研究內容有: （ 1 ）本課題所要研究的內容包括:磁感噴油器的設計;針閥升程信號、主軸轉速信號、噴油壓力信號的採集與處理;系統硬體電路的設計;軟體編程等。 -
( 2 ) relation of quantity of fuel injection and needle vavle lift, rotation speed and pressure is got
（ 2 ）測定噴油量與針閥升程、噴油時間、主軸轉速、噴油壓力的關系。 -
The technical line of the thesis is as follows : formula of quantity of fuel injection is got by studying relation of quantity of fuel injection and needle valve lift, time of fuel injection, rotation speed and pressure, and quantity of fuel injection is displayed
本課題研究的技術路線為:通過研究噴油量與針閥升程、噴油時間、主軸轉速、噴油壓力等的關系，推導出精確的噴油量計算公式，最終由顯示器顯示噴油量。 -
The authors carry out data collection and calculation for fuel injection pressure and needle valve lift signals measured on the fuel pump test bed by using self - developed software. on the basis of experiments, four criteria for analysing fuel injection process are proposed and the comparison of performances between au and nu type fuel outlet valves is made
作者用自行開發的軟體對在油泵試驗臺上測得的噴油壓力、針閥升程信號進行了數據採集和計算，在試驗的基礎上提出了分析噴油過程的四個判據，給出了au型和nu型出油閥的性能比較結果。 -
Install a needle valve in the control line. if uneven pressure should cause the regulator to pulsate, its action can be stabilized by throttling the valve
在控制管線上安裝一個針形閥。如果不穩定的壓力導致調節閥波動，則這種波動通過對閥門節流將穩定下來。
分享友人